[mrtg] Re: Help with connecting to a Cisco 2610 series router

[Bruce B. Platt]

At 03:53 PM 12/28/1999 -0600, Huy Vo wrote:


I added snmp-server anable traps snmp

and it didn't help

Thanks for your response


->I don't run MRTG on any newer Cisco 2611 (The 2611 shipped with IOS 12.x)
->
->HP Openview had the same problem that it could not response to any SNMP
->command
->even though I had:
->
->snmp-server community xxxx RO  on the router
->
->After I add the following line to the 2611,'s config:
->
->snmp-server enable traps snmp
->
->then this device would response to any SNMP request.  Isn't it strange? Did
->not need this on any IOS 11.x
->
->Add the above line to your Cisco config to see if it solves your problem.
->
->Huy Vo
->Principal Network Engineer
->mailto:huy_vo at pagenet.com
->
->
->
->> -----Original Message-----
->> From:	Bruce B. Platt [SMTP:bbp at comport.com]
->> Sent:	Tuesday, December 28, 1999 3:48 PM
->> To:	mrtg at list.ee.ethz.ch
->> Subject:	[mrtg] Help with connecting to a Cisco 2610 series router
->> 
->> I am successfully running mrtg with my Cisco 2501 running IOS v 11.3.
->> 
->> We just received a Cisco 2611 and I'd like to monitor that as well.
->> 
->> When I run cfgmaker I get no response from the Cisco 2611.  I have used
->> the
->> snmp community string as
->> shown by the show config command and cfgmaker fails as follows:
->> 
->> SNMP Error:
->> no response received
->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" [www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 1955278080
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> SNMPGET Problem for sysDescr sysContact sysName sysLocation ifNumber
->> sysObjectID on public at www.xxx.yyy.zzz
->> SNMP Error:
->> no response received
->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" [www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 848782245
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> SNMP Error:
->> no response received
->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" [www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 848782246
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> 
->> The router has the following only line referencing snmp in it's
->> configuration:
->> 
->> snmp-server community public RO
->> 
->> Does anyone know of any thing peculiar to this series of routers?
->> 
->> cfgmaker still works just fine on my 2501.
->> 
->> Thanks and regards,
->> 
->> Bruce
->> 
->> --
->> Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
->> Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
->> Archive     http://www.ee.ethz.ch/~slist/mrtg

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
Archive     http://www.ee.ethz.ch/~slist/mrtg