[mrtg] Re: Ascend Pipeline 130

[Justin Shore]

I don't know if this is relevant here but when I did the following on 
one of the 130's I just setup MRTG for it failed to return every port:

[www at Vinnie www]$ snmpwalk 208.46.69.10 <snip>
system.sysDescr.0 = "Ascend Pipeline BRI S/N: 9665673 Software +6.1.19+"
system.sysObjectID.0 = OID: enterprises.529.1.3.7
system.sysUpTime.0 = Timeticks: (506597400) 58 days, 15:12:54.00
system.sysContact.0 = "Gene 3165842255"
system.sysName.0 = "pipe130-brd.clr"
system.sysLocation.0 = "Clearwater KS"
system.sysServices.0 = 14
interfaces.ifNumber.0 = 22
interfaces.ifTable.ifEntry.ifIndex.1 = 1
interfaces.ifTable.ifEntry.ifIndex.2 = 2
interfaces.ifTable.ifEntry.ifDescr.1 = "Console 1"
interfaces.ifTable.ifEntry.ifDescr.2 = "BRI Slot 1 Line 1"
interfaces.ifTable.ifEntry.ifType.1 = 33
interfaces.ifTable.ifEntry.ifType.2 = basicISDN(20)

But I could snmpget a specific interface and it would find it: (not 
that .3 doesn't exist)

[www at Vinnie www]$ snmpget 208.46.69.10 <snip> 
interfaces.ifTable.ifEntry.ifDescr.4 
interfaces.ifTable.ifEntry.ifDescr.4 = "ie0" Hex: 69 65 30

[www at Vinnie www]$ snmpget 208.46.69.10 <snip> 
interfaces.ifTable.ifEntry.ifDescr.5 
interfaces.ifTable.ifEntry.ifDescr.5 = "wan0" Hex: 77 61 6E 30

That put a dumb look on my face.  Frankly I don't care to know why 
just so long as it still works. :-)

Justin


At 11:27 AM -0500 2/2/00, Neil Calvert wrote:
>as long as it supports Mib-2, the standard frame relay DTE mib should
>give the data you need.
>
>'frInOctets' => '1.3.6.1.2.1.10.32.2.1.9'
>'frOutOctets' => '1.3.6.1.2.1.10.32.2.1.7'
>
>which when used in the form:
>
>frInOctets.pp.dd&frOutOctets.pp.dd:community at cisco.router
>
>where pp is the physical port that the frame relay pvc is
>defined on and dd is the DLCI of the pvc gets you the in
>and out octets for just that pvc.
>
>(from the documentation)
>
>-----Original Message-----
>From: Dan Spray <cpdans at conpoint.com>
>To: mrtg at list.ee.ethz.ch <mrtg at list.ee.ethz.ch>
>Date: Wednesday, February 02, 2000 11:15 AM
>Subject: [mrtg] Ascend Pipeline 130
>
>
>  >Does anyone use MRTG to monitor the WAN port for a pipeline 130. I need
>to
>  >monitor a 56K frame relay. Basically I need an OID that works, if there
>is
>  >one out there. Any help would be greatly appreicated.
>  >Thanks in advance,
>  >Dan
>  >
>  >
>  >--
>  >Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
>  >Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
>  >Archive     http://www.ee.ethz.ch/~slist/mrtg
>  >
>
>--
>Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
>Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
>Archive     http://www.ee.ethz.ch/~slist/mrtg


--
Justin Shore
K-State Linux Distro Mirror, Sysadmin
macdaddy at vinnie.ksu.ksu.edu
<http://vinnie.ksu.ksu.edu/mirror/rpm2html>
<ftp://vinnie.ksu.ksu.edu/pub/mirror/linux>

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
Archive     http://www.ee.ethz.ch/~slist/mrtg