[mrtg] Config error causes Perl to DR.Watson

Tue Nov 27 19:52:21 MET 2001

I am trying to get FECNs and BECNs from a CIsco 3620 router using the config
shown below.  When I run MRTG I get the following error:

Snmp Error
No Respone Received
Snmp V2c_session <remotehost: "172.16.101.88" [172.16.101.88].161>
Community "da1sy"
etc...
Snmpget problem for IfHciOctets.5 ifHcOOctects.5 sysUptime sysName on
da1sy at 172.16.101..88

Right after these error messages I get 
Perl.exe  Dr. Watson
Exception Access Violation (0xc0000005) addrss 0x28030a47

Here is the config that I am running:
workdir: \\beitechserv\webdata\netdata
options[_]: integer, nopercent, gauge
MaxBytes[_]: 50000
YLegend[_]: FECNs & BECNs
ShortLegend[_]: Frames 
Legend1[_]: Incomming FECNs
Legend2[_]: Incomming BECNs 
Legend3[_]: Maximal 5 Minute Incoming FECNs 
Legend4[_]: Maximal 5 Minuter Outgoing BECNs
LegendI[_]: &nbsp;FECNs:
LegendO[_]: &nbsp;BECNs:

######################################################################
# System: Facility QA Lab
# Description: Image: rel/13.01/ Created on Thu Oct 22 17:00:53 EDT 1998.
# Contact: Bob Mersberger 501 -201 -3442
# Location: Fort Smith AR
######################################################################

### Interface 2 >> Descr: 'S11' | Name: '' | Ip: '172.16.101.88' | Eth:
'00-00-a2-62-84-31' ###

Target[getdlci2]:
.1.3.6.1.2.1.10.32.2.1.4.2.101&.1.3.6.1..2.1.10.32.2.1.5.2.101:da1sy at 172.16.
101.88
SetEnv[getdlci2]: MRTG_INT_IP="172.16.101.88" MRTG_INT_DESCR="Frame relay"

Title[getdlci2]: FECN and BECN Report -- 
PageTop[getdlci2]: <H1>FECN and BECN Report -- </H1>
 <TABLE>
   <TR><TD>System:</TD>     <TD>CBO-7509 Nashville KY.</TD></TR>
   <TR><TD>Maintainer:</TD> <TD>Bob Mersberger 501 -201 -3442</TD></TR>
   <TR><TD>Description:</TD><TD>S11  </TD></TR>
   <TR><TD>ifType:</TD>     <TD>frame-relay (32)</TD></TR>
   <TR><TD>ifName:</TD>     <TD></TD></TR>
   <TR><TD>Max Speed:</TD>  <TD>56.0 kbits/s</TD></TR>
   <TR><TD>Ip:</TD>         <TD>172.16.101.88()</TD></TR>
 </TABLE>

****************************************************************************
*********************************************
I can get the information successfully when I do an Snmpget from my
management workstation but not with MRTG. I have tried with and without
:::::2 but get same basic results.  

Can anyone tell me what I might be doing wrongs.  I have fought this problem
for 2 days now.

Robert (Bob) Mersberger
LAN Consultant
Beverly Enterprises, Inc.
1000 Beverly Way
Fort Smith, AR 72919 
Ph. 501-201-3442
Fax: 501-478-3837
Email Robert_Mersberger at Beverlycorp.com

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi