[mrtg] Re: Chassis Status

Zeng Xing NCS xzeng at ncs.com.sg
Wed Feb 20 04:39:36 MET 2002



Hi,

I just found out that Chassis status can be accessed via the Cisco
Environmental MIB Group: cicsoEnvMonMIB.

-----Original Message-----
From: Zeng Xing NCS [mailto:xzeng at ncs.com.sg]
Sent: Wednesday, February 20, 2002 10:00 AM
To: 'Paul C. Williamson'; mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Chassis Status




yes, I am checking the IOS version for the supported SNMP features. so far
we know it is not supported for 2610 and 2620.  

-----Original Message-----
From: Paul C. Williamson [mailto:pwilliamson at mandtbank.com]
Sent: Wednesday, February 20, 2002 9:45 AM
To: mrtg at list.ee.ethz.ch; xzeng at ncs.com.sg
Subject: Re: RE: [mrtg] Re: Chassis Status


It actually depends on a few things...

What version of IOS you are running, what hardware, what filters you have
applied...

Some support all of that (and more, some support none).

Paul

>>> Zeng Xing  NCS <xzeng at ncs.com.sg> 02/19/02 20:42 PM >>>

I am using Getif, it shows me nothing when I poll chassisFanStatus. But when
I poll against Cisco switches, I can see some value. Probably the chassis
status SNMP support is not implemented in Cisco routers.


-----Original Message-----
From: Paul C. Williamson [mailto:pwilliamson at mandtbank.com]
Sent: Tuesday, February 19, 2002 8:49 PM
To: mrtg at list.ee.ethz.ch; xzeng at ncs.com.sg
Subject: [mrtg] Re: Chassis Status



How are you trying to poll it?  With snmpget, GetIf, 
SNMPc, or something else?  Usually, you need to add 
a .0 to the end of the OID.  Don't forget that MRTG 
requires two values for each target, so putting 
in one OID in the target line will cause all kinds 
of errors to pop up.

Paul

>>> Zeng Xing NCS <xzeng at ncs.com.sg> 02/19/02 04:31 AM >>>


Hi,

I am wondering if there is a way to monitor the chassis status(fan, power
supply and module status) of Cisco routers(26xx, 75xx, 72xx, 36xx). I was
trying to poll the MIB variable ChassisFanStatus etc, but it didn't give me
any value. Can someone kindly advise me how to get it work?

Thanks in advance!!

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ        http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi



More information about the mrtg mailing list