[mrtg] Re: temp not working on cisco 7200

[john.hoffman at za.pwcglobal.com]

Options should not be "bits", use the "Gauge"  (See you have Options in the
config twice - will also cause failure in MRTG).

Another point which you find useful;
Instead of graphing just the inlet temperature =
1.3.6.1.4.1.9.9.13.1.3.1.3.1
replace the second OID with Outlet temperature =
1.3.6.1.4.1.9.9.13.1.3.1.3.2

Regards
John



                                                                                                                                       
                      MegaNet DomainReg                                                                                                
                      <domainreg at meganet       To: mrtg at list.ee.ethz.ch                                                                
                      .net>                    cc:                                                                                     
                      Sent by:                 Subject:  [mrtg] temp not working on cisco 7200                                         
                      mrtg-bounce at list.e                                                                                               
                      e.ethz.ch                                                                                                        
                      2002/03/18 06:15                                                                                                 
                      PM                                                                                                               
                                                                                                                                       
                                                                                                                                       
                                                                                                                                       



 Size: 4 Kb



Ok i have the following temp config for a cisco, this was working fine
suddenly it stop, now i can only get it to graph 30 degrees F all the time.
I use this config on other ciscos and it still is working fine, any ideas
why it would stop working out of no where.

thanks

RunAsDaemon: yes
Interval: 5
WriteExpires: yes
Refresh: 300

WorkDir: /var/www/html/mrtg2/ciscotemp/frv
Options[_]: bits, growright
Target[frv.cisco.temp]:
1.3.6.1.4.1.9.9.13.1.3.1.3.1&1.3.6.1.4.1.9.9.13.1.3.1.3.1:xxx at x.x.x.x * 1.8
+ 32
YLegend[frv.cisco.temp]: Deg. F
ShortLegend[frv.cisco.temp]: F
MaxBytes[frv.cisco.temp]: 200
Options[frv.cisco.temp]: gauge, nopercent
Title[frv.cisco.temp]: BOSTON gateway : Inlet Temp
Colours[frv.cisco.temp]: VIOLET#ff00ff,GREEN#00eb0c,BLUE#1000ff,BLUE#1000ff


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi




----------------------------------------------------------------
         The information transmitted is intended only for the person or
         entity to which it is addressed and may contain confidential
         and/or privileged material.  Any review, retransmission,
         dissemination or other use of, or taking of any action in reliance
         upon, this information by persons or entities other than the
         intended recipient is prohibited.   If you received this in error,
         please contact the sender and delete the material from any
         computer.


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi