[mrtg] Re: 3com Superstack 3 4400 and MRTG

[Simon ter Veen]

Hi...

what du you want to monitor - just the traffic of the ports?

in that case:
I'm monitoring the port's traffic of several 3com 4400 without any Problems.
below is an extract of one of my cfg files - i hope that can help u.
I'm still using mrtg-2.9.18pre4 which works fine for me :) *never run a changing system:)*
And i have to admit that im still a MRTG/SNMP newbie so tis might not be the perfect cfg file :)


######START OF FILE######


# Created by StV
# cfgmaker --show-op-down public at 192.168.1.122 --global 'HtmlDir: C:\www\mrtg\linsw02 ImageDir: C:\www\mrtg\linsw02\images LogDir: C:\www\mrtg\linsw02\logs' --output linsw02.cfg
# indexmaker --output=C:\www\mrtg\linsw02.html linsw02.cfg 

######################################################################
# System: LINSW02
# Description: 3Com SuperStack 3 4400
# Contact: Admin
# Location: ServerRaum
######################################################################


### Interface 101 >> Descr: 'RMON Port 01 on unit 1' | Name: '' | Ip: '' | Eth: '' ###

Target[192.168.1.122_101]: 101:public at 192.168.1.122:
SetEnv[192.168.1.122_101]: MRTG_INT_IP="" MRTG_INT_DESCR="RMON Port 01 on unit 1"
MaxBytes[192.168.1.122_101]: 12500000
Title[192.168.1.122_101]: Traffic Analysis for 101 -- LINSW02
PageTop[192.168.1.122_101]: <H1>Traffic Analysis for 101 -- LINSW02</H1>
 <TABLE>
   <TR><TD>System:</TD>     <TD>LINSW02 in ServerRaum</TD></TR>
   <TR><TD>Maintainer:</TD> <TD>Admin</TD></TR>
   <TR><TD>Description:</TD><TD>RMON Port 01 on unit 1  </TD></TR>
   <TR><TD>ifType:</TD>     <TD>ethernetCsmacd (6)</TD></TR>
   <TR><TD>ifName:</TD>     <TD></TD></TR>
   <TR><TD>Max Speed:</TD>  <TD>12.5 MBytes/s</TD></TR>
 </TABLE>
.
.
.
.
.
HtmlDir: C:\www\mrtg\linsw02 
ImageDir: C:\www\mrtg\linsw02\images 
LogDir: C:\www\mrtg\linsw02\logs

#######END OF FILE#########



regards,
Simon ter Veen

-----Original Message-----
From: Chris Visser [mailto:chrisv at absol.co.za]
Sent: Wednesday, November 20, 2002 3:37 PM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] 3com Superstack 3 4400 and MRTG



Hi,

I'm trying to monitor my new 3com Superstack 3 4400 switch using MRTG,
the same way I did with my Superstack 2 3300.

I tried just running cfgmaker like I did before and it couldn't setup
anything.  So I RTFMed and found out I needed the MIB files for the
switch, so I downloaded them, but how to use them to help configure MRTG
is just confusing me at the moment.

Could someone please help me out either by explaining the easy way to
monitor my switch or pointing me in the right direction for other
documentation....

Thanks in advance
Chris

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi