[mrtg] Re: mrtg rrdtool mrtg-rrd.cgi

[Aldo Salinas]

I modified the mrtg-rrd.cgi use lib to point to where my rrds.pm file is.
Now I get the page but it does not display the graphs.  What do i need to
check for now?

-----Original Message-----
From: Will Saxon [mailto:WillS at housing.ufl.edu]
Sent: Friday, September 06, 2002 9:49 AM
To: Aldo Salinas; Mrtg at List. Ee. Ethz. Ch (E-mail)
Subject: RE: [mrtg] mrtg rrdtool mrtg-rrd.cgi


mrtg-rrd requires that you put the config files you want to see specifically
in the .cgi file itself. Then, you access the page by:

http://your.webserver.com/<your_cgi_dir>/mrtg-rrd.cgi

The index page generated by mrtg-rrd.cgi uses the same daily graphs as the
detailed pages do, whereas 14all uses a smaller, legendless graph (at least
by default - is this changeable?).

The output from mrtg-rrd is a little easier on my eyes, though probably a
little less precise (?). I actually like it better. However, the (perceived)
precision and the ability to specify config files in the url were so
important to us that we are using 14all instead, until we figure out how to
modify mrtg-rrd to accept url parameters or write our own cgi. 

Also, using mod_perl it seems like 14all might be a little faster than
mrtg-rrd. I don't know if I have FastCGI set up correctly though, so it may
be using 'normal' cgi. mrtg-rrd quit working altogether when I installed
mod_perl and told it to handle all .cgi files. 

-Will



> -----Original Message-----
> From: Aldo Salinas [mailto:aesalinas at plant.pp.panam.edu]
> Sent: Friday, September 06, 2002 10:38 AM
> To: Mrtg at List. Ee. Ethz. Ch (E-mail)
> Subject: [mrtg] mrtg rrdtool mrtg-rrd.cgi
> 
> 
> 
> I've successfully configured mrtg with rrdtool and 14all.cgi. 
>  It works just
> the way I want to, but now I want to try mrtg-rrd.cgi I want 
> to see the
> difference between them but I cant seem to figure out how to 
> access the
> output from mrtg-rrd.cgi.  Can anyone out there give me a 
> hand?  What do I
> need to type on the address bar to see the graphs?  This is 
> really a stupid
> question, but bare with me since I'm not too familiar with 
> mrtg, rrdtool, or
> even cgi's   :)   at least not yet.
> 
> Redhat 7.2
> MRTG 2.9.22
> RRDTOOL 1.0.39
> mrtg-rrd.cgi 0.5
> 
> I want to thank everyone for your time and help.
> 
> 
> Aldo
> 
> --
> Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
> Archive     http://www.ee.ethz.ch/~slist/mrtg
> FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
> WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi
> 
> 

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi