[mrtg] Re: MRTG config for 1720?
Michael Markstaller
mm at elabnet.de
Tue Apr 29 21:24:59 MEST 2003
Asaf,
this depends on you display-frontend; there's nothing in these templates supressing percentages from interface-traffic to get displayed.. with 14all.cgi and mrtg-rrd.cgi it works fine here.
You can either create a single cfg&index file with cfgmaker/indexmaker manually for each device or automated as it's done with exact the commands/templates I sent, when you use it that way every host goes into one directory which causes the above mentioned cgis to display them seperately..
Michael
-----Original Message-----
From: Asaf Rapoport [mailto:arapoport at telepacific.com]
Sent: Tuesday, April 29, 2003 9:06 PM
To: Michael Markstaller
Subject: RE: [mrtg] Re: MRTG config for 1720?
Michael,
The template works well, however is there a way to show % until and not just kb/mb on Ser and eth ports?
Also is there a way to create an index page per device instead of indexing all on one page?
-----Original Message-----
From: Michael Markstaller [mailto:mm at elabnet.de]
Sent: Tuesday, April 29, 2003 1:23 AM
To: "Lotierzo, Leandro (Administración del Centro de Cómputos)"; Asaf
Rapoport; mrtg at list.ee.ethz.ch
Subject: RE: [mrtg] Re: MRTG config for 1720?
Hi, I already posted this a few days ago (subject CRC errors). I did a host-template which includes among other things CPU (1min/5min) and Proc/IOmem-usage and works fine for every Cisco-router from 805 to Cat5RSM; it inserts the Maxbytes for Proc/IOmem based on the value the router actually provides via snmp with calcing used+free mem giving you right percentages. (but this should be run best when the router is reloaded freshly)
Templates can be found at:
-- Desc: host-genericsnmp.template.ElabNET
-- Size: 29k (30709 bytes)
-- URL : http://www.ee.ethz.ch/~slist/p/host-genericsnmp.template.ElabNET
-- Desc: interface-genericsnmp.template.ElabNET
-- Size: 18k (18951 bytes)
-- URL : http://www.ee.ethz.ch/~slist/p/interface-genericsnmp.template.ElabNET
Use with (one line)
"/usr/local/mrtg/bin/cfgmaker --ifdesc=descr --if-template=/usr/local/mrtg/cfg-template/interface-genericsnmp.template.ElabNET --host-template=/usr/local/mrtg/cfg-template/host-genericsnmp.template.ElabNET --community='xxx' --subdirs=HOSTNAME router1 router2 router3 >> /usr/local/mrtg/mrtg_temp_cfg
Michael
-----Original Message-----
From: "Lotierzo, Leandro (Administración del Centro de Cómputos)"
[mailto:LLotierzo at lanacion.com.ar]
Sent: Tuesday, April 29, 2003 3:44 AM
To: 'mrtg at list.ee.ethz.ch '
Subject: [mrtg] Re: MRTG config for 1720?
Importance: High
I have this CFG working with a Router Cisco 1750.
#---------------------------------------------------------------
# CPU Usage RouterName1750 Creado x LL el 11/09/2002
#---------------------------------------------------------------
Target[CPU-RouterName1750]:
1.3.6.1.4.1.9.2.1.57.0&1.3.6.1.4.1.9.2.1.58.0:SnmpComunity at 10.10.10.10
YLegend[CPU-RouterName1750]: CPU % Util.
ShortLegend[CPU-RouterName1750]: %
MaxBytes[CPU-RouterName1750]: 100
Options[CPU-RouterName1750]: nopercent, gauge, growright
Unscaled[CPU-RouterName1750]: dwmy
Legend1[CPU-RouterName1750]: CPU %:
Legend2[CPU-RouterName1750]: .
Legend3[CPU-RouterName1750]: Max value per interval on graph
Legend4[CPU-RouterName1750]: .
LegendI[CPU-RouterName1750]: CPU %:
LegendO[CPU-RouterName1750]: .
Title[CPU-RouterName1750]: RouterName1750 CPU
PageTop[CPU-RouterName1750]: <H1>RouterName1750 CPU</H1>
Colours[CPU-RouterName1750]:
GREEN#00eb0c,BLUE#0000ff,GRAY#AAAAAA,VIOLET#ff00ff
Background[CPU-RouterName1750]: #FFFFFF
WithPeak[CPU-RouterName1750]: ymw
#---------------------------------------------------------------
# MEM Usage RouterName1750 Creado x LL el 11/09/2002
#---------------------------------------------------------------
Target[MEM-RouterName1750]:
1.3.6.1.4.1.9.9.48.1.1.1.5.0&1.3.6.1.4.1.9.9.48.1.1.1.5.0:SnmpComunity at 10.10
.10.10 * 100 / 8281228 (This is the total Mem)
YLegend[MEM-RouterName1750]: Memory % Used
ShortLegend[MEM-RouterName1750]: Used
MaxBytes[MEM-RouterName1750]: 100
Options[MEM-RouterName1750]: nopercent, gauge, growright
Unscaled[MEM-RouterName1750]: dwmy
Legend1[MEM-RouterName1750]: Memory Utilized
Legend2[MEM-RouterName1750]: .
Legend3[MEM-RouterName1750]: Max value per interval on graph
Legend4[MEM-RouterName1750]: .
LegendI[MEM-RouterName1750]: Mem.%:
LegendO[MEM-RouterName1750]: .
Title[MEM-RouterName1750]: RouterName1750 MEM
PageTop[MEM-RouterName1750]: <H1>RouterName1750 MEM</H1>
Colours[MEM-RouterName1750]:
GREEN#00eb0c,BLUE#0000ff,GRAY#AAAAAA,VIOLET#ff00ff
Background[MEM-RouterName1750]: #FFFFFF
WithPeak[MEM-RouterName1750]: ymw
LL
SysAdmin at LN
-----Original Message-----
From: Asaf Rapoport [mailto:arapoport at telepacific.com]
Sent: Monday, April 28, 2003 10:38 PM
To: 'Ross Tsolakidis '
Cc: 'mrtg at list.ee.ethz.ch '
Subject: [mrtg] Re: MRTG config for 1720?
Thank you Ross!
Anyone out there having better luck with the 1720?
-----Original Message-----
From: Ross Tsolakidis
To: Asaf Rapoport
Cc: mrtg at list.ee.ethz.ch
Sent: 4/28/03 5:04 PM
Subject: RE: MRTG config for 1720?
Hi Asaf,
For the 1720 I found a config for the CPU, but not sure it's working
100%. The numbers just seem low..
Here it is.
## CPU usage
Target[*.*.*.*_cpu]:
1.3.6.1.4.1.9.2.1.57.0&1.3.6.1.4.1.9.2.1.58.0:public@*.*.*.*
YLegend[*.*.*.*_cpu]: CPU Utilization
ShortLegend[*.*.*.*_cpu]: %
MaxBytes[*.*.*.*_cpu]: 100
Options[*.*.*.*_cpu]: nopercent, gauge, unknaszero
#Unscaled[*.*.*.*_cpu]: dwmy
Legend1[*.*.*.*_cpu]: CPU Utilization
Legend2[*.*.*.*_cpu]: .
Legend3[*.*.*.*_cpu]: Max value per interval on graph
Legend4[*.*.*.*_cpu]: .
LegendI[*.*.*.*_cpu]: CPU:
LegendO[*.*.*.*_cpu]: .
Title[*.*.*.*_cpu]: CPU load %
PageTop[*.*.*.*_cpu]: <H1>CPU load %</H1>
Colours[*.*.*.*_cpu]: GREEN#00eb0c,BLUE#0000ff,GRAY#AAAAAA,VIOLET#ff00ff
WithPeak[*.*.*.*_cpu]: ymw
--
I had much more luck with the 7206.
Target[*.*.*.*.cpu]:
1.3.6.1.4.1.9.2.1.56.0&1.3.6.1.4.1.9.2.1.56.0:public@*.*.*.*
MaxBytes[*.*.*.*.cpu]: 100
Title[*.*.*.*.cpu]: 7206psmel - CPU Usage (%)
YLegend[*.*.*.*.cpu]: CPU Usage (%)
ShortLegend[*.*.*.*.cpu]: %
Legend2[*.*.*.*.cpu]: CPU Usage
LegendO[*.*.*.*.cpu]: Usage:
Options[*.*.*.*.cpu]: nopercent, gauge
SetEnv[*.*.*.*.cpu]: MRTG_INT_IP="*.*.*.*" MRTG_INT_DESCR="CPU Usage"
PageTop[*.*.*.*.cpu]: <H1>7206psmel - CPU Usage (%)</H1>
<TABLE>
<TR><TD>System:</TD> <TD>7206psmel </TD></TR>
<TR><TD>Description:</TD><TD>CPU Usage </TD></TR>
</TABLE>
#---------------------------------------------------------------
Target[*.*.*.*.mem]:
.1.3.6.1.4.1.9.9.48.1.1.1.5.1&.1.3.6.1.4.1.9.9.48.1.1.1.6.1:public@*.*.*
.*
MaxBytes[*.*.*.*.mem]: 256000000
Title[*.*.*.*.mem]: 7206psmel - MEM Free Usage (%) Max MEM = 256000K
YLegend[*.*.*.*.mem]: MEM Usage (MB)
LegendO[*.*.*.*.mem]: Free MEM:
LegendI[*.*.*.*.mem]: Used MEM:
Options[*.*.*.*.mem]: nopercent,gauge
PageTop[*.*.*.*.mem]: <H1>7206psmel - MEM Free Usage (%) Max MEM =
256000K </H1>
<TABLE>
<TR><TD>System:</TD> <TD>7206psmel </TD></TR>
<TR><TD>Description:</td><TD>Memory Usage </TD></TR>
</TABLE>
#---------------------------------------------------------------
#7000 1.3.6.1.4.1.9.9.13.1.3.1.3.1 Inlet Temp degrees Centigrade
# 1.3.6.1.4.1.9.9.13.1.3.1.3.2 Outlet Temp degrees Centigrade
Target[*.*.*.*.temp]:
1.3.6.1.4.1.9.9.13.1.3.1.3.1&1.3.6.1.4.1.9.9.13.1.3.1.3.2:public@*.*.*.*
YLegend[*.*.*.*.temp]: Degrees C
ShortLegend[*.*.*.*.temp]: °C
MaxBytes[*.*.*.*.temp]: 50
Options[*.*.*.*.temp]: nopercent, gauge
Unscaled[*.*.*.*.temp]: dwmy
AbsMax[*.*.*.*.temp]: 50
Title[*.*.*.*.temp]: 7206psmel Temperature Sensors
Colours[*.*.*.*.temp]:
GREEN#00eb0c,BLUE#1000ff,BLUE#1000ff,VIOLET#ff00ff
Legend1[*.*.*.*.temp]: Average 1 minute Inlet Temperature
Legend2[*.*.*.*.temp]: Average 1 minute Outlet Temperature
Legend3[*.*.*.*.temp]: Average 5 minute Inlet Temperature
Legend4[*.*.*.*.temp]: Average 5 minute Outlet Temperature
LegendI[*.*.*.*.temp]: Inlet:
LegendO[*.*.*.*.temp]: Outlet:
PageTop[*.*.*.*.temp]: <H1> Temperature - Degrees C </H1>
<TABLE>
<TR><TD>System:</TD><TD>7206psmel</TD></TR>
<TR><TD>Description:</TD><TD>Temperature Sensors </TD></TR>
</TABLE>
---
I had some help from a gentlemen on this list, but for the life of me I
can't remember his name :(
Sorry :)
--
Ross.
-----Original Message-----
From: Asaf Rapoport [mailto:arapoport at telepacific.com]
Sent: Tuesday, 29 April 2003 5:55 AM
To: Ross Tsolakidis
Cc: 'mrtg at list.ee.ethz.ch'
Subject: MRTG config for 1720?
Hello Ross,
Were you able to find the config for CPU / Mem on a 1720?
How about a 7206?
_____
[ <http://www.ee.ethz.ch/~slist/mrtg/msg19099.html> Date Prev][
<http://www.ee.ethz.ch/~slist/mrtg/msg19101.html> Date Next][
<http://www.ee.ethz.ch/~slist/mrtg/msg19103.html> Thread Prev][
<http://www.ee.ethz.ch/~slist/mrtg/msg19104.html> Thread Next][
<http://www.ee.ethz.ch/~slist/mrtg/mail3.html#19100> Date Index][
<http://www.ee.ethz.ch/~slist/mrtg/thrd77.html#19100> Thread Index]
[mrtg] cisco 1720 cpu config
_____
* To: "' mrtg at list.ee.ethz.ch <mailto:mrtg at list.ee.ethz.ch> '" <
mrtg at list.ee.ethz.ch <mailto:mrtg at list.ee.ethz.ch> >
* Subject: [mrtg] cisco 1720 cpu config
* From: Ross Tsolakidis < rtsolakidis at powerserve.com.au
<mailto:rtsolakidis at powerserve.com.au> >
* Date: Mon, 8 Jul 2002 09:29:11 +1000
* Delivered-To: slist at ee.ethz.ch
* Sender: mrtg-bounce at list.ee.ethz.ch
<mailto:mrtg-bounce at list.ee.ethz.ch>
Hi all,
I'm having trouble getting mrtg to graph cpu usage on a Cisco 1720
Router.
Has anyone accomplished this, is it possible ?
If so, can get the values and a sample config ? :)
Thanks.
--
Ross.
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
<mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe>
Archive http://www.ee.ethz.ch/~slist/mrtg
<http://www.ee.ethz.ch/~slist/mrtg>
FAQ http://faq.mrtg.org <http://faq.mrtg.org/> Homepage
http://www.mrtg.org <http://www.mrtg.org/>
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
<http://www.ee.ethz.ch/~slist/lsg2.cgi>
* Prev by Date: [mrtg] Making scripts
<http://www.ee.ethz.ch/~slist/mrtg/msg19099.html> 64-bit counters
* Next by Date: [mrtg] Re: Making
<http://www.ee.ethz.ch/~slist/mrtg/msg19101.html> scripts 64-bit
counters
* Prev by thread: [mrtg] Re: Making
<http://www.ee.ethz.ch/~slist/mrtg/msg19103.html> scripts 64-bit
counters
* Next by thread: [mrtg] Question about
<http://www.ee.ethz.ch/~slist/mrtg/msg19104.html> monitoring laserjet
printers
* Index(es):
* <http://www.ee.ethz.ch/~slist/mrtg/mail3.html#19100> Date
* <http://www.ee.ethz.ch/~slist/mrtg/thrd77.html#19100> Thread
Thank you,
Asaf Rapoport
Internal Communications
Phone: (213) 213-3278
Fax: (213) 213-3279
If you could really accept that you weren't ok
you could stop proving you were ok.
If you could stop proving that you were ok
you could get that it was ok not to be ok.
If you could get that it was ok not to be ok
you could get that you were ok the way you are.
You're ok, get it? ~Werner Erhard 1973
Recipe for success: Study while others are sleeping; work while others
are loafing; prepare while others are playing; and dream while others
are wishing.
--William A. Ward
In life: smart people learn from their mistakes while intelligent people
learn from other people's mistakes. Which one are you? - Asaf
Rapoport
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
More information about the mrtg
mailing list