[mrtg] Re: Util graph for a tunnel interface.--help needed.

[Kerry Werry]

Nope it just means that is what the router reports via SNMP, you will have
the full BW you have available.

KLW

Kerry L. Werry MCSE CCNA
Pivotal Corporation



-----Original Message-----
From: AS, Raj Kumar [mailto:RajKumar at solectron.com] 
Sent: January 28, 2003 10:28 PM
To: Greg_Mersberger at i2.com
Cc: mrtg at list.ee.ethz.ch; mrtg-bounce at list.ee.ethz.ch
Subject: [mrtg] Re: Util graph for a tunnel interface.--help needed.


Does that mean the maximum BW I can have is 9K? If I change the BW to 128K
in the router can I use upto 128K.

I think its better to change that on the mrtg config file. suggestions??

Best Regards,
Raj.


-----Original Message-----
From: Greg_Mersberger at i2.com [mailto:Greg_Mersberger at i2.com]
Sent: Wednesday, January 29, 2003 1:51 PM
To: AS, Raj Kumar
Cc: mrtg at list.ee.ethz.ch; mrtg-bounce at list.ee.ethz.ch
Subject: Re: [mrtg] Util graph for a tunnel interface.--help needed.



The default bandwidth setting for a tunnel interface is 9k (Cisco platform).
You can either add a bandwidth statement on your tunnel interface (be aware
of the routing metric impact) or just change your config file.

Hope this helps

Greg




 

                      "AS, Raj Kumar"

                      <RajKumar at solectr        To:
mrtg at list.ee.ethz.ch

                      on.com>                  cc:

                      Sent by:                 Subject:  [mrtg] Util graph
for a tunnel interface.--help needed.                       
                      mrtg-bounce at list.

                      ee.ethz.ch

 

 

                      01/28/2003 11:24

                      PM

 

 





Hi Group,

I have  router with a tunnel interface to another location. I was told that
the BW of the tunnel is 128K. I want to plot the util graph using MRTG. When
I run MRTG and create the config file I find the following info below..

System:            XXXXX- in
Maintainer:
Description:             Tunnel10 Tunnel to XXXXX-R1
ifType:            Other (1)
ifName:            Tu10
Max Speed:         1125.0 Bytes/s
Ip:          x.x.x.x ()

Why is that the Max speed is only 9Kb (1125Bytes).

Can somebody help. Thanks for the time..

Best Regards,
Raj.



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi






--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi