[mrtg] Re: Disk Utilization For WinNT

Alegria, Luis lalegria at ics-canada.net
Fri May 23 17:37:19 MEST 2003


Austin

Check the latest drivers for your NIC Card. I had a similar problem before,
where I could not pull anything from a server. It was because the old driver
that I had installed did not support SNMP. Once I Update them, SNMP4nt pull
tons of stuff out of it. I also recommend that you use GETIF instead of
snmpwalk.

Luis Alegria
ICS courier Services
LAN Admin.

-----Original Message-----
From: Manny Ortega [mailto:aortega at univ-wea.com] 
Sent: Friday, May 23, 2003 11:18 AM
To: 'wolfe at daticon.com'; mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Disk Utilization For WinNT

MS and SNMP have never played well togethet until W2K SP3.
May I suggest http://www.wn.com.au/psimmo/
You can log data using Windows Performance Monitor and graph it with MRTG.

-MannyO

-----Original Message-----
From: wolfe at daticon.com [mailto:wolfe at daticon.com]
Sent: Friday, May 23, 2003 10:09 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Disk Utilization For WinNT


I have tried this. When I look at the OID list using snmpwalk, I only see
the same ones that were there before I installed snmp4tpc. I even set up a
new WinNT 4.0 server so I could do this from scratch. No go. I followed the
instructions on the site and checked the troubleshooting page. Any ideas?

Austin Wolfe

-----Original Message-----
From: fluhmann at vvm.com [mailto:fluhmann at vvm.com]
Sent: Thursday, May 22, 2003 4:06 PM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Disk Utilization For WinNT


Try looking at http://www.snmp4tpc.com/  and click on SNMP4NT.  It will
install the MIB's for you to be able to monitor performance on NT.

Hope that helps,
Jeremy Fluhmann
McLane Information Systems Division


wolfe at daticon.com wrote:

>Hello Group,
>	I look ed at the Somix WinNT disk utilization MRTG config but my
>WinNT 4.0 server does not seem to have the OIDs. I have done an SNMPwalk
and
>did not find them. Has anyone here set up MRTG to monitor disk utilization
>of a WinNT 4.0 box? If so, how did you do it?
>
>Thank,
>Austin Wolfe
>



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi



More information about the mrtg mailing list