[mrtg] Re: Vijay - mrtg with Sonicwall Pro 3060

[Vijay Ramnarayan]

Hi,

Thanks for the response. 
Have done all this and rechecked it many times the error is still the
same.  
How can we verify whether mrtg is supporting the Sonicwall Pro 3060 box
? 
Where is the mib database stored ? 

Regards,
Vijay.

-----Original Message-----
From: mrtg-bounce at list.ee.ethz.ch [mailto:mrtg-bounce at list.ee.ethz.ch]
On Behalf Of Scott Neader
Sent: Thursday, February 02, 2006 9:22 PM
To: Vijay Ramnarayan; mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Vijay - mrtg with Sonicwall Pro 3060 

Vijay, I've been able to get it to work on a smaller SonicWALL TZ-170.
No MIB was needed.  However, you have to configure the SonicWALL to
allow SNMP from the outside. Make sure you go under NETWORK > INTERFACES
> WAN and under the GENERAL tab, check the box for SNMP.  Then, go under
SYSTEM > ADMINISTRATION > and check the box for SNMP.  Then click
CONFIGURE and check your GET COMMUNITY NAME (no need for TRAP COMMUNITY
NAME in this scenario).  You can also add IP ADDRESSES under HOST 1,
HOST 2, HOST 3, HOST 4 for your MRTG machine(s)

Let me know if I can assist further.

- Scott




mrtg-bounce at list.ee.ethz.ch wrote on Thursday, February 02, 2006 9:21
AM: 
> Hi,
> 
> I am trying to configure my Sonicwall Pro 3060 box 3.1.0.11
> Enhanced Image  in mrtg 2.10.15-1 on a RHEL 4 system. When I
> run mrtg from the linux box I get the following error :
> 
> [root at ftp etc]# env LANG=C mrtg /etc/mrtg/mrtg.cfg SNMP Error: no
> response received SNMPv1_Session (remote host: "10.10.1.2"
>                   [10.10.1.2].161) community: "public"
>                  request ID: 1430333680
>                 PDU bufsize: 8000 bytes
>                     timeout: 2s
>                     retries: 5
>                     backoff: 1)
>  at /usr/bin/../lib/mrtg2/SNMP_util.pm line 490 SNMPGET
> Problem for ifInOctets.1 ifOutOctets.1 sysUptime sysName on
> public at 10.10.1.2::::::v4only  at /usr/bin/mrtg line 1846
> WARNING: skipping because at least the query for ifInOctets.1 on
> 10.10.1.2 did not succeed
> WARNING: no data for ifInOctets&ifOutOctets:public at 10.10.1.2.
> Skipping further queries for Host 10.10.1.2 in this round.
> ERROR: Target[r1][_IN_] ' $target->[0]{$mode} ' did not eval into
> defined data ERROR: Target[r1][_OUT_] ' $target->[0]{$mode} ' did not
> eval into defined data [root at ftp etc]#
> 
> a) Please let mw know how do I find out the mib of Sonicwall
> in mrtg is
>    correct ?
> 
> b) I have setup the box correctly and Sonicwall has confirmed
> that they have seen it working in various environments
> although officially they donot support mrtg.
> 
> Kindly help.
> 
> Regards,
> Vijay.

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://lists.ee.ethz.ch/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://lists.ee.ethz.ch/lsg2.cgi



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://lists.ee.ethz.ch/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://lists.ee.ethz.ch/lsg2.cgi