[mrtg] Want to monitor System temperature of 2811 router - Need OID

Tue Aug 26 19:31:39 CEST 2008

You may have it on something and I will try it. the 2811 has only one
oid for the temp and it is 
cisco.ciscoMgmt.13.1.3.1.3.1 : Unsigned32: 22

Will I have to do anything special with the template for mrtg or will I
need to add anything to routers.cgi to get this to graph this?

________________________________

From: Anson Rinesmith [mailto:arinesmith at bigrivertelephone.com] 
Sent: Tuesday, August 26, 2008 12:18 PM
To: Mersberger, Robert; 'Steve Shipway'; mrtg at lists.oetiker.ch
Subject: RE: [mrtg] Want to monitor System temperature of 2811 router -
Need OID

I use these for my 7206, might get lucky and work for you.

Cisco 7206vxr router:
                     CPU: 1.3.6.1.4.1.9.2.1.58.0
                     Mem: 1.3.6.1.4.1.9.9.48.1.1.1.5.1
           Temp intake  1: 1.3.6.1.4.1.9.9.13.1.3.1.3.1
           Temp exhaust 2: 1.3.6.1.4.1.9.9.13.1.3.1.3.2
           Temp exhaust 3: 1.3.6.1.4.1.9.9.13.1.3.1.3.3
           Temp exhaust 4: 1.3.6.1.4.1.9.9.13.1.3.1.3.4

________________________________

From: mrtg-bounces at lists.oetiker.ch
[mailto:mrtg-bounces at lists.oetiker.ch] On Behalf Of Mersberger, Robert
Sent: Tuesday, August 26, 2008 12:09 PM
To: Steve Shipway; mrtg at lists.oetiker.ch
Subject: [mrtg] Want to monitor System temperature of 2811 router - Need
OID

I would like to monitor the system temperature that is shown when one
doe the show env command on the router.

Would anyone know the OID that I would need to use to accomplish this or
maybe have a better solution. 

I tried looking through the results of an snmpwalk for the router but
that was of little help.

If someone can help I would appreciate it.

________________________________

From: mrtg-bounces at lists.oetiker.ch
[mailto:mrtg-bounces at lists.oetiker.ch] On Behalf Of Hughes, Andy
Sent: Friday, August 22, 2008 10:06 AM
To: Steve Shipway; 'mrtg at lists.oetiker.ch'
Subject: Re: [mrtg] Newbie question

Steve, thanks again. I have changed the task to run every 5 minutes,
which currently means it fails every 5 minutes.

Here is a snippet that appears after manually trying to run (community
string and IP changed). The hosting provider swears they have not
altered the community string.  Does anything look obviously wrong?

SNMPv1_Session (remote host: "10.10.10.10" [10.10.10.10].161)
                  community: "xxxxxxx"
                 request ID: 1304582469
                PDU bufsize: 8000 bytes
                    timeout: 2s
                    retries: 5
                    backoff: 1)
 at C:/mrtg-2.16.2/bin\..\lib\mrtg2/SNMP_util.pm line 492
SNMPGET Problem for ifInOctets.1 ifOutOctets.1 sysUptime sysName on
xxxxxxx at 10.10.10.10::::::v4only <mailto:xxxxxxx at 10.10.10.10::::::v4only>

 at mrtg line 2202
2008-08-19 09:04:54: WARNING: skipping because at least the query for
ifInOctets
.1 on  10.10.10.10 did not succeed
2008-08-19 09:04:54: WARNING: no data for
ifInOctets&ifOutOctets:xxxxxxx at 1
0.10.10.10. Skipping further queries for Host 10.10.10.10 in this round.

________________________________

From: Steve Shipway [mailto:s.shipway at auckland.ac.nz] 
Sent: Friday, August 22, 2008 12:36 AM
To: Hughes, Andy; 'mrtg at lists.oetiker.ch'
Subject: RE: Newbie question

The location of error logs depends on your system setup; I can't help
you there.

MRTG will poll at 5min intervals by default only if you are using Daemon
mode (you arent).  Therefore, you should set your cron job to run every
5 mins, unless you have explicitly set a 10min interval (you havent).

Steve

________________________________

From: mrtg-bounces at lists.oetiker.ch [mrtg-bounces at lists.oetiker.ch] On
Behalf Of Hughes, Andy [Andrew.Hughes at aquilent.com]
Sent: Friday, 22 August 2008 5:15 a.m.
To: 'mrtg at lists.oetiker.ch'
Subject: Re: [mrtg] Newbie question

Steve, thanks very much for the response.  I will pursue what you have
suggested.

I did search for some error logs but found none. Where are they hiding?

Is mrtg by default going to run every 5 minutes without my intervention,
or are you saying I should change the task to run every 5 minutes
instead rather than the 10 I set up?

Thanks again!

Please consider the environment before printing this e-mail. 

CONFIDENTIAL NOTICE:
This e-mail message and any attachment(s) (collectively, this 'Email')
are intended 
only for the confidential use of the recipient(s) named above. If the
reader of this 
message is not the intended recipient named above or an agent
responsible for 
delivering it to the intended recipient named above, you have received
this Email in error. 
Please notify the sender immediately and permanently delete this Email
and any copies thereof.

Please consider the environment before printing this e-mail.

CONFIDENTIAL NOTICE:
This e-mail message and any attachment(s) (collectively, this 'Email') are intended
only for the confidential use of the recipient(s) named above. If the reader of this
message is not the intended recipient named above or an agent responsible for
delivering it to the intended recipient named above, you have received this Email in error.
Please notify the sender immediately and permanently delete this Email and any copies thereof.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.oetiker.ch/pipermail/mrtg/attachments/20080826/938b228d/attachment.html 