[mrtg] AW: Re: Help with connecting to a Cisco 2610 series router

[Grischa Schuering]

You probably need a RW community (write access is needed by mrtg)!!

greetings,

grischa

> -----Ursprüngliche Nachricht-----
> Von: Bruce B. Platt [mailto:bbp at comport.com]
> Gesendet: Dienstag, 28. Dezember 1999 23:40
> An: Huy Vo
> Cc: 'mrtg at list.ee.ethz.ch'
> Betreff: [mrtg] Re: Help with connecting to a Cisco 2610 series router
> 
> 
> At 03:53 PM 12/28/1999 -0600, Huy Vo wrote:
> 
> 
> I added snmp-server anable traps snmp
> 
> and it didn't help
> 
> Thanks for your response
> 
> 
> ->I don't run MRTG on any newer Cisco 2611 (The 2611 shipped 
> with IOS 12.x)
> ->
> ->HP Openview had the same problem that it could not response 
> to any SNMP
> ->command
> ->even though I had:
> ->
> ->snmp-server community xxxx RO  on the router
> ->
> ->After I add the following line to the 2611,'s config:
> ->
> ->snmp-server enable traps snmp
> ->
> ->then this device would response to any SNMP request.  Isn't 
> it strange? Did
> ->not need this on any IOS 11.x
> ->
> ->Add the above line to your Cisco config to see if it solves 
> your problem.
> ->
> ->Huy Vo
> ->Principal Network Engineer
> ->mailto:huy_vo at pagenet.com
> ->
> ->
> ->
> ->> -----Original Message-----
> ->> From:	Bruce B. Platt [SMTP:bbp at comport.com]
> ->> Sent:	Tuesday, December 28, 1999 3:48 PM
> ->> To:	mrtg at list.ee.ethz.ch
> ->> Subject:	[mrtg] Help with connecting to a Cisco 2610 
> series router
> ->> 
> ->> I am successfully running mrtg with my Cisco 2501 running 
> IOS v 11.3.
> ->> 
> ->> We just received a Cisco 2611 and I'd like to monitor 
> that as well.
> ->> 
> ->> When I run cfgmaker I get no response from the Cisco 
> 2611.  I have used
> ->> the
> ->> snmp community string as
> ->> shown by the show config command and cfgmaker fails as follows:
> ->> 
> ->> SNMP Error:
> ->> no response received
> ->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" 
[www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 1955278080
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> SNMPGET Problem for sysDescr sysContact sysName sysLocation ifNumber
->> sysObjectID on public at www.xxx.yyy.zzz
->> SNMP Error:
->> no response received
->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" [www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 848782245
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> SNMP Error:
->> no response received
->> SNMPv1_Session (remote host: "www.xxx.yyy.zzz" [www.xxx.yyy.zzz].161
->>                   community: "public"
->>                  request ID: 848782246
->>                 PDU bufsize: 8000 bytes
->>                     timeout: 2s
->>                     retries: 5
->>                     backoff: 1)
->> 
->> The router has the following only line referencing snmp in it's
->> configuration:
->> 
->> snmp-server community public RO
->> 
->> Does anyone know of any thing peculiar to this series of routers?
->> 
->> cfgmaker still works just fine on my 2501.
->> 
->> Thanks and regards,
->> 
->> Bruce
->> 
->> --
->> Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
->> Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
->> Archive     http://www.ee.ethz.ch/~slist/mrtg

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
Archive     http://www.ee.ethz.ch/~slist/mrtg

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Help        mailto:mrtg-request at list.ee.ethz.ch?subject=help
Archive     http://www.ee.ethz.ch/~slist/mrtg