[mrtg] Cisco CPU Utilization

[Martinez, Samson]

I made the upgrade from 2.8.12 to 2.9.4 (will go to .5 shortly) but I've
encountered a small speed bump and I just can't figure it out. It's probably
a no-brainer but I'm breaking down and asking for assistance :-)... Anyway,
we have been monitoring numerous Cisco routers and switches with 2.8.12,
processor utilization included. This was the original script section
responsible for CPU monitoring and it worked great in 2.8.12:
 
Target[cisco_device]:
1.3.6.1.4.1.9.2.1.56.0&1.3.6.1.4.1.9.2.1.56.0:community at x.x.x.x
SetEnv[cisco_device]: MRTG_INT_IP="x.x.x.x" MRTG_INT_DESCR="Processor
Utilization"
MaxBytes[cisco_device]: 100
WithPeak[cisco_device]: ym
Options[cisco_device]: growright,gauge,noinfo,nopercent,absolute
Unscaled[cisco_device]: dwmy
ShortLegend[cisco_device]: &#40%&#41
YLegend[cisco_device]: % Utilization
Legend1[cisco_device]:  Percent Router CPU Utilization
LegendI[cisco_device]:  Utilization: 
LegendO[cisco_device]:
Title[cisco_device]: cisco device blah 
PageTop[cisco_device]: <H1>  Device CPU Utilization
 </H1>
 <TABLE>
   <TR><TD>System:</TD><TD>Blah (CPU Utilization) </TD></TR>
   <TR><TD>Maintainer:</TD><TD>Me</TD></TR>
   <TR><TD>IP:</TD><TD>x.x.x.x</TD></TR>
  </TABLE>
 
The graphic showed only the "Percent Router CPU Utilization" indicator.
However, in 2.9.4, I now see "Maximal Incoming", "Maximal Outgoing", and
"Outgoing Traffic in Bytes per Second" listed as well. Granted, the only
thing being graphed is the CPU utilization but I can't seem to get these
entries off of the graphic. I changed the script a bit to look like this but
it still happens:
 
Target[cisco_device]:
1.3.6.1.4.1.9.2.1.56.0&1.3.6.1.4.1.9.2.1.56.0:community at x.x.x.x
SetEnv[cisco_device]: MRTG_INT_IP="x.x.x.x" MRTG_INT_DESCR="Processor
Utilization"
MaxBytes[cisco_device]: 100
WithPeak[cisco_device]: ymwd
Options[cisco_device]: growright, gauge
Unscaled[cisco_device]: ymwd
ShortLegend[cisco_device]: %
YLegend[cisco_device]: % Utilization
Legend1[cisco_device]:  Percent Switch CPU Utilization
Legend2[cisco_device]:
Legend3[cisco_device]:
Legend4[cisco_device]:
Title[cisco_device]: Device CPU Utilization
PageTop[cisco_device]: <H1>  Device CPU Utilization
 </H1>
 <TABLE>
   <TR><TD>System:</TD><TD>Blah (CPU Utilization) </TD></TR>
   <TR><TD>Maintainer:</TD><TD>Me</TD></TR>
   <TR><TD>IP:</TD><TD>x.x.x.x</TD></TR>
  </TABLE>
 
Please assist. Many thanks.
 
Regards,
 
Samson 
 


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi