[mrtg] Re: Multiple routers with one CFG file

[Mitch Erickson]

Thanks again:
Yes Both of the CFG files work perfect independently, and I have used the >>
with the cfgmaker to create a common CFG file.
I am attempting to monitor the same OID on both (separate) routers.
If I run the multiple CFG file with different IP addresses It complains,
however, if I change the CFG file so that both of the Targets have the same
address it works ?
Thanks
mitch

 -----Original Message-----
From: 	Paul C. Williamson [mailto:pwilliamson at MANDTBANK.COM] 
Sent:	Thursday, July 20, 2000 9:41 AM
To:	merickso at cucentral-ab.com; mrtg at list.ee.ethz.ch
Subject:	[mrtg] Re: Multiple routers with one CFG file

Are you trying to monitor two separate routers, or one router with two
separate OIDs?

Can you test both router IP addresses in two different cfg files?  Do both
IP addresses work independently of each other, outside the cfg file where
they both reside?

Paul

>>> Mitch Erickson <merickso at cucentral-ab.com> 07/20/00 11:24AM >>>

Paul:
Thank you very much for your help,
Unfortunately for me however, it is still the same.
The strange thing is that when I use my CFG file for two routers, with
different addresses I get the error. If on the other hand, I change one of
the addresses so both are the same, it works fine ?

The error indicates a bad file descriptor, so I checked all of my paths and
such but they are OK.
Does any one else have any Ideas ?

Thanks once again for every ones time.
mitch

 -----Original Message-----
From: 	Paul C. Williamson [mailto:pwilliamson at MANDTBANK.COM] 
Sent:	Thursday, July 20, 2000 6:03 AM
To:	merickso at cucentral-ab.com 
Subject:	Re: [mrtg] Multiple routers with one CFG file

 << File: wmsville.cfg >> Yes, I have attached a cfg file from my site.  I
monitor up to 50 routers with one cfg file.  If you run cfgmaker, instead of
directing it to a file (with ">") and then try to join the two, append
directly from cfgmaker (with ">>") and all will be fine.

Paul

>>> Mitch Erickson <merickso at cucentral-ab.com> 07/19/00 04:44PM >>>

Hello:

I would like to try this once again as I did not really get any responses to
my previous email.

First, is anyone able to pull stats from multiple routers (of different IP
addresses) using one CFG file. I have tried this and can not get it to work.
I always get an error.
I have read the DOC, and have attempted to merge the two CFG files that were
created for two routers. Individually both CFG files work fine, however,
when I place them together I get an error:

close: Bad file descriptor
SNMPv1_Session (remote host: "10.1.1.1" [10.1.1.1].161
                  community: "test"
                 request ID: 2068631264
                PDU bufsize: 8000 bytes
                    timeout: 2s
                    retries: 5
                    backoff: 1)

Thanks once again, but I am sure that I must be over looking something very
simple.
Oh yes I am using version 2.8.10 for NT.

Mitch erickson

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe 
Archive     http://www.ee.ethz.ch/~slist/mrtg 
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org 
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi 



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe 
Archive     http://www.ee.ethz.ch/~slist/mrtg 
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org 
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi 


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi