[mrtg] Re: CPU Utilization. (OID's for this and more!)

[Jason Frisvold]

Here is the OID for Cisco CPU Utilization (1 minute and 5 minute) as well as
quite a few others we found to be useful..  :)  My suggestion is to do a
manual SNMP Get and GetNext on them.  Some of these require an additional
"port" tagged onto the end.

Ciscos :

CPU (5 Minute)		1.3.6.1.4.1.9.2.1.58.0
CPU (1 Minute)		1.3.6.1.4.1.9.2.1.57.0

Per interface:
ifInErrors			1.3.6.1.2.1.2.2.1.14
ifOutErrors			1.3.6.1.2.1.2.2.1.20

Should also graph in and out discards per interface.
ifInDiscards		1.3.6.1.2.1.2.2.1.13
ifOutDiscards		1.3.6.1.2.1.2.2.1.19

Per router:
ipOutDiscards		1.3.6.1.2.1.4.11
ipInDiscards		1.3.6.1.2.1.4.8

Temp in			1.3.6.1.4.1.9.9.13.1.3.1.3.1
Temp Out			1.3.6.1.4.1.9.9.13.1.3.1.3.2
Hotpoint			1.3.6.1.4.1.9.9.13.1.3.1.3.3	(Only on
some routers)

Fore:
ATMTRAFFICIN		1.3.6.1.4.1.326.2.2.2.1.2.2.1.12.PORT
ATMFRAFFICOUT		1.3.6.1.4.1.326.2.2.2.1.2.2.1.18.PORT
ATMCPU			1.3.6.1.4.1.326.2.2.1.1.1.3.1.2

3Com Hiper Arcs :
nmcStatTemperature	1.3.6.1.4.1.429.2.2.5
Ethernet1			3:
Ethernet2			4:

Best UPS :
upsOutputPercentLoad		1.3.6.1.4.1.2947.4.9	(Percentage of the
total UPS power capacity being used - integer expressed in % of 100)
upsBatteryRuntimeRemaining	1.3.6.1.4.1.2947.2.3	(remaining time in
minutes UPS will be able to run on battery - integer in minutes remaining)

APC UPS :
mUpsEnvironAmbientTemperature		1.3.6.1.4.1.318.1.1.2.1.1	(The
ambient temperature in celsius)
mUpsEnvironRelativeHumidity		1.3.6.1.4.1.318.1.1.2.1.2	(The
relative humidity as a percentage)

---------------------------
Jason H. Frisvold
Head ATM Engineer
Engineering Dept.
Penteledata
friz at corp.ptd.net
---------------------------
"Only two things are infinite, the universe and human stupidity, and I'm not
sure about the former." - Albert Einstein


-----Original Message-----
From: Matt Holmquist [mailto:mattho at InfoAve.Net]
Sent: Thursday, June 29, 2000 8:47 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] CPU Utilization.



Hello,

	I have just joined the list and have a question. How do I set up
MRTG to
read CPU utilization on a Cisco router? In the documents that I have, it
mentions that you need an OID number, but I do not kow where to pull that
value from. (ie: OID_1&OID_2:public at 192.168.1.1) If this question has
already been covered, then can someone direct me to where in the archives I
can look.

Thanks,

Matthew M. Holmquist, CCNA
Consulting Engineer
Info Avenue Internet Services
http://www.infoave.net
mattho at infoave.net

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi