[mrtg] R: Re: monitoring PRI on cisco 3640

[Marco Lanata]

Neil,

thank you for your rapid answer. I'd like to graph the total ISDN trafic, as
you said, but I do not understand how to "point MRTG at the physical port
that the ISDN PRI is configured on and pull ifInOctets and ifOutOctets from
it". I'm new to SNMP.

Can you please send me some more instructions or (which would be very
appreciated !!) the confgiguration I should use in mrtg.cfg ?
I can send you my mrtg.cfg file, if you think that it should be useful.

I thank you in advance for your patience.

Best regards.
____________________________
Marco Lanata
Virtual srl
Tel. +39-0185-368005
Fax +39-0185-368107
e-mail : marco at tigullio.it
http://www.tigullio.it
____________________________


-----Messaggio originale-----
Da: mrtg-bounce at list.ee.ethz.ch [mailto:mrtg-bounce at list.ee.ethz.ch]Per
conto di Calvert, Neil
Inviato: martedì 30 maggio 2000 14.57
A: Marco Lanata
Cc: mrtglist (E-mail)
Oggetto: [mrtg] Re: monitoring PRI on cisco 3640


If you want to graph the TOTAL ISDN traffic then probably the easiest way to
do that is to point MRTG at the physical port that the ISDN PRI is
configured on and pull ifInOctets and ifOutOctets from it. That should give
you the sum of all the traffic going over the port. (Some devices implement
this differently however so be careful that those Mib objects behave in this
way for this device).

If you want to break it down by ISDN channel, you will have to point a MIB
browser (like GetIf) at the device to find out what the interface numbers
are. Most devices with sub-interfacing technology (ISDN, Frame Relay) will
construct the Mib-2/Interfaces tree with all the physical ports and logical
interfaces. You then give the appropriate instance to the OID to allow MRTG
to graph it.


Neil
-----Original Message-----
From: Marco Lanata [mailto:marco at tigullio.it]
Sent: Tuesday, May 30, 2000 8:49 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] monitoring PRI on cisco 3640


Hi,

I have MRTG up and running on windows 2000 server. It is monitoring my cisco
3640 ports (1 ethernet and 4 serial line). I'd like to monitor also the
traffic passing on my PRI (Primary ISDN access - 25 anolog/digital lines).

Is there anyone out there who can provide me the configuration ? I have
tried with default, but the system give me one graph for each different line
and not the whole amount.

I thank you in advance.

____________________________
Marco Lanata
Virtual srl
Tel. +39-0185-368005
Fax +39-0185-368107
e-mail : marco at tigullio.it
http://www.tigullio.it
____________________________


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org