[mrtg] Re: NT and the MRTG_totalizer???

[Dowling, Steve]

Andre,

I loved it until that last caveat 
"Runs lovely on linux, but kills proc on NT (mouse movement dead)."

Steve Dowling

-----Original Message-----
From: Andre Coetzee [mailto:andrec at emailco.co.za]
Sent: Friday, 31 August 2001 16:54
To: 'mrtg at list.ee.ethz.ch'
Subject: [mrtg] Re: NT and the MRTG_totalizer???



Oops, missed one thing ...

Add the following #-# lines to your eth.cfg file and replace router.ser2 
with your router name ip etc.

Label heading for page
#-#Total[router.ser2]: Traffic Totals for ROUTER, 2 Mbit E1 to Internet  
Calculated amount kilobytes(K)/MegaBytes(M)
#-#Total-Unit[router.ser2]: M
Additional IN/OUT ratio
#-#Total-Ratio[router.ser2]:yes

Runs lovely on linux, but kills proc on NT (mouse movement dead).

Andre

-----Original Message-----
From: Andre Coetzee [mailto:andrec at emailco.co.za]
Sent: 31 August 2001 08:49
To: 'mrtg at list.ee.ethz.ch'
Subject: [mrtg] Re: NT and the MRTG_totalizer???



Howdy,

This is actually a very awesome script.

Josef helped me out with getting the IN's and OUT's right and so it also
dates back months.

Anyway, what you need installed is the script and Active State Perl for
Win32, 
I think version 6.2 or something higher is fine.

Then open a command prompt and type in 'ppm' and in the prompt type in 

'install GD'
'install GDGraph'
'install GDGraph3d'
'install GDTextUtil'

Once installed fine, put the script in your mrtg bin directory and run
perl mrtg_total.pl eth.cfg

Then look in the path stated in your eth.cfg file for the compiled html and
gif/png files.

normally eth.total.2001.html or something like that.

Thanks to Josef for such a good script.

Regards
Andre

-----Original Message-----
From: Chad Markley [mailto:cmarkley at thinkecs.com]
Sent: 31 August 2001 12:22
To: 'mrtg at list.ee.ethz.ch'
Subject: [mrtg] NT and the MRTG_totalizer???



I am trying to get the MRTG totalizer working on NT 4.0,
http://www.geocities.com/josef_wendel/. I am having a really hard time
getting the required perl programs installed. Does anyone have any
experience with this script? Or, does anyone know of a better program to get
totals from your log files?

Thanks
Chad Markley


--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi