[mrtg] Re: oid for temperature on a cisco 6509?

[Trever Furnish]

Thanks, but unfortunately those don't seem to work for the 6509 (although
the first two work fine for the 7513).  Is there any general resource or
point of contact within Cisco that anyone on the list knows of for making
inquiries like this one, other than asking the TAC?  Although I admit this
is a rather trival question...

-t.


-----Original Message-----
From: David Sawyer [mailto:david.sawyer at uk.mckhboc.com]
Sent: Tuesday, March 06, 2001 4:29 AM
To: 'Trever Furnish'; MRTG List
Subject: RE: [mrtg] oid for temperature on a cisco 6509?


I don't have an environment card installed in any of our routers, but...

Have you tried the OID with a 0 (zero) on the end, ie
1.3.6.1.4.1.9.9.13.1.3.1.2.0
## This is listed as "ciscoEnvMonTemperatureStatusDescr"

1.3.6.1.4.1.9.9.13.1.3.1.3.0
## This is listed as "ciscoEnvMonTemperatureStatusValue"

Have you tried...

envTestPt1Descr = 1.3.6.1.4.1.9.2.1.78
envTestPt1Measure = 1.3.6.1.4.1.9.2.1.79
## Typically ambient air or the temperature of air entering the router

envTestPt2Descr = 1.3.6.1.4.1.9.2.1.80
envTestPt2Measure = 1.3.6.1.4.1.9.2.1.81
## Typically airflow or the temperature of air leaving the router

envTestPt3Descr = 1.3.6.1.4.1.9.2.1.82
envTestPt3Measure = 1.3.6.1.4.1.9.2.1.83
## Typically the value in millivolts of the +5v supply

envTestPt4Descr = 1.3.6.1.4.1.9.2.1.84
envTestPt4Measure = 1.3.6.1.4.1.9.2.1.85
## Typically the value in millivolts of the +12v supply

envTestPt5Descr = 1.3.6.1.4.1.9.2.1.86
envTestPt5Measure = 1.3.6.1.4.1.9.2.1.87
## Typically the value in millivolts of the -12v supply

envTestPt6Descr = 1.3.6.1.4.1.9.2.1.88
envTestPt6Measure = 1.3.6.1.4.1.9.2.1.89
## Typically the value in millivolts of the -5v supply

HTH
Dave

> -----Original Message-----
> From:	Trever Furnish [SMTP:trever at wowemployers.com]
> Sent:	Monday, March 05, 2001 9:18 PM
> To:	MRTG List
> Subject:	[mrtg] oid for temperature on a cisco 6509?
>
>
> On our Cisco 7513 I was able to figure out that the following two OIDs
> give
> some temperature data.  However, even though my 6509 also show similar
> output when I issue the "show environment all" EXEC command, I these oids
> return no values.  Is there another oid that works for the 6509?
>
> Oids that work on the 7513:
> .1.3.6.1.4.1.9.9.13.1.3.1.2.1 - RSP inlet temp in C.
> .1.3.6.1.4.1.9.9.13.1.3.1.3.3 - RSP exhaust temp in C.
>
> Anyone got anything similar for the 6509?
>
>
----------------------------------------------------------------------------
The information contained in this e-mail is confidential and is intended
only for the named recipient(s). If you are not the intended recipient you
must not copy, distribute, or take any action or reliance on it.
If you have received this e-mail in error, please notify the sender.
Any unauthorised disclosure of the information contained in this e-mail
is strictly prohibited.
----------------------------------------------------------------------------



--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi