[mrtg] Re: cisco4006
Manny Jimenez
mannyj at wizguys.com
Tue Dec 17 17:28:57 MET 2002
OOPS, just checked the cisco website and there is IOS code for SUP III only.
Anyway, the following IOS commands should work fine:
snmp-server community (yourcommunity) RO
snmp-server community (yourcommunity) RW
Good luck,
Manny
Cisco Catalyst 4000 only run with CATOS code. There is an RSM (Route Switch
Module) available for the 4000 which runs IOS code, just like a cisco 3600.
Here are the commands:
CAT 4000
set snmp community read-only (yourcommunity)
set snmp community read-write (yourcommunity)
RSM
snmp-server community (yourcommunity) RO
snmp-server community (yourcommunity) RW
Have fun...
Manny
-----Original Message-----
From: mrtg-bounce at list.ee.ethz.ch [mailto:mrtg-bounce at list.ee.ethz.ch]On
Behalf Of Brander, Eric
Sent: Tuesday, December 17, 2002 10:37 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: cisco4006
Bah, nevermind
-----Original Message-----
From: Brander, Eric [mailto:Eric.Brander at ACS-INC.com]
Sent: Tuesday, December 17, 2002 9:31 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: cisco4006
I run a Sup3, supports IOS only. There is no CatOS on my 4006.
-----Original Message-----
From: Matt Katona [mailto:mkatona at comwavz.com]
Sent: Tuesday, December 17, 2002 9:36 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: cisco4006
4006 runs CatOS unless you are referring to a MSFC card, which is a layer 3
router card and runs IOS. With this card you can have two logical addresses,
the one for the layer2 CatOS and one for the layer3 IOS card. They are
independent of each other in that regard.
-----Original Message-----
From: Brander, Eric [mailto:Eric.Brander at ACS-INC.com]
Sent: Tuesday, December 17, 2002 10:16 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: cisco4006
Are you certain you have SNMP enabled and that "public" is the correct RO
string? My 4006 is running IOS so the command is different, but this is
what I use:
snmp-server community public RO
-----Original Message-----
From: Jean-Hugues BELPOIS [mailto:Jean-Hugues.Belpois at univ-brest.fr]
Sent: Tuesday, December 17, 2002 2:32 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: cisco4006
All the router are running CatOS, but when I try to use cfgmaker as
indicated
(./cfgmaker --ifref=name --ifdesc=descr --descint --output=/var/mrtg/another
cat.cfg public at 172.30.3.1) it cause the errors messages :
--base: Get Device Info on public at 172.30.3.1
SNMP Error:
no response received
SNMPv1_Session (remote host: "172.30.3.1" [172.30.3.1].161)
community: "public"
request ID: 703847423
PDU bufsize: 8000 bytes
timeout: 2s
retries: 5
backoff: 1)
SNMPGET Problem for sysDescr sysContact sysName sysLocation sysObjectID on
public at 172.30.3.1
--base: Vendor Id:
--base: Populating confcache
SNMP Error:
no response received
etc..
And a strange thing (for me) that it work fine withe the other routers 3548,
connected to the 4006.
Is anybody got an idea of what is wrong ?
jhb
----- Original Message -----
From: "McDonald, Dan" <Dan.McDonald at austinenergy.com>
To: "'Jean-Hugues BELPOIS'" <Jean-Hugues.Belpois at univ-brest.fr>
Sent: Monday, December 16, 2002 2:00 PM
Subject: RE: [mrtg] cisco4006
Running IOS or CatOS?
Either way, cfgmaker does a fine job with:
./cfgmaker --ifref=name --ifdesc=descr --descint
--output=/var/mrtg/anothercat.cfg public at 10.10.10.10
Daniel J McDonald, CCIE #2495, CNX
Lan/Wan Integrator
Austin Energy
1.512.322.6739
dan.mcdonald at austinenergy.com
-----Original Message-----
From: Jean-Hugues BELPOIS [mailto:Jean-Hugues.Belpois at univ-brest.fr]
Sent: Monday, December 16, 2002 6:17 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] cisco4006
Hello,
Is anybody use mrtg with à cisco 4006 catalyst and can send me an example
of
his mrtg.cfg file ?
thanks a lot
jhb
----------------------------------------------------------------------------
-------
Jean-Hugues BELPOIS
Département informatique - I.U.P d'ingénierie informatique
U.F.R sciences - Batiment LC
Université de Bretagne Occidentale
20, Avenue Victor Le Gorgeu 29285 Brest Cedex
Tel : 02.98.01.69.70 Fax : 02.98.01.80.11
Mail : belpois at univ-brest.fr
----------------------------------------------------------------------------
-------
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
More information about the mrtg
mailing list