[mrtg] Re: Config Maker (6509 temperature)
Hart, Kevin
KHart at helixtechnology.com
Thu Jan 23 17:53:06 MET 2003
Kerry,
I haven't been graphing this stuff for a while, since my MRTG box crashed in
October and I
had to rebuild it but, good point, now that you mention it.
I've also got two identical 6509 switches in the same room with two
different input exhaust temps?? The temps do not seem to change (at least in
the last 30 SNMP gets).
I'm going to run this for a while and check the values.
Thanks,
Kevin
Here is the actual output from the snmp gets of five different 6500 switches
intake temp slot 1.
C:\>snmputil get x.x.6.100 community .1.3.6.1.4.1.9.9.91.1.1.1.1.4.1001
Variable = .iso.org.dod.internet.private.enterprises.9.9.91.1.1.1.1.4.1001
Value = INTEGER - 19
C:\>snmputil get x.x.6.101 community .1.3.6.1.4.1.9.9.91.1.1.1.1.4.1001
Variable = .iso.org.dod.internet.private.enterprises.9.9.91.1.1.1.1.4.1001
Value = INTEGER - 25
C:\>snmputil get x.x.6.102 community .1.3.6.1.4.1.9.9.91.1.1.1.1.4.1001
Variable = .iso.org.dod.internet.private.enterprises.9.9.91.1.1.1.1.4.1001
Value = INTEGER - 24
C:\>snmputil get x.x.6.150 community .1.3.6.1.4.1.9.9.91.1.1.1.1.4.1001
Variable = .iso.org.dod.internet.private.enterprises.9.9.91.1.1.1.1.4.1001
Value = INTEGER - 24
C:\>snmputil get x.x.6.151 community .1.3.6.1.4.1.9.9.91.1.1.1.1.4.1001
Variable = .iso.org.dod.internet.private.enterprises.9.9.91.1.1.1.1.4.1001
Value = INTEGER - 23
-----Original Message-----
From: Kerry Werry [mailto:KWerry at Pivotal.com]
Sent: Thursday, January 23, 2003 10:44 AM
To: 'Hart, Kevin'
Cc: 'mrtg at list.ee.ethz.ch'
Subject: RE: [mrtg] Re: Config Maker (6509 temperature)
Kevin
I have used a similar config in the past and have just tried yours and while
the configs have always produced an graph I have NEVER seen the value
change..... Even during an AC failure the value stayed constant. Have you or
anyone else actually seen this work??
KLW
Kerry L. Werry MCSE CCNA
Pivotal Corporation
-----Original Message-----
From: Hart, Kevin [mailto:KHart at helixtechnology.com]
Sent: January 22, 2003 6:33 AM
To: 'Crow Lee Contr 379 ECS'; mrtg at list.ee.ethz.ch
Subject: [mrtg] Re: Config Maker
Hi,
Here is a config example for monitoring exhaust temp for slot 1. This works
on a 6509, so I'm assuming it will work on the 6513 as well. Note that the
temp is converted to Fahrenheit at the end. Just remove the * 1.8 + 32 at
the end of the target if you want Celsius.
Kevin
Target[6509_exhaust_temp_slot1]:1.3.6.1.4.1.9.9.91.1.1.1.1.4.1002&1.3.6.1.4.
1.9.9.91.1.1.1.1.4.1002:community at ip_address * 1.8 + 32
Directory[6509_exhaust_temp_slot1]: 6509_Environmental
Unscaled[6509_exhaust_temp_slot1]: d
MaxBytes[6509_exhaust_temp_slot1]: 100
AbsMax[6509_exhaust_temp_slot1]: 150
ShortLegend[6509_exhaust_temp_slot1]: F
YLegend[6509_exhaust_temp_slot1]: Temp Fahrenheit
Legend2[6509_exhaust_temp_slot1]: Temp Fahrenheit
LegendI[6509_exhaust_temp_slot1]: Temp 
LegendO[6509_exhaust_temp_slot1]:
Options[6509_exhaust_temp_slot1]: gauge, noo, nopercent, nobanner
Title[6509_exhaust_temp_slot1]: Cat6509 Slot 1 Exhaust Temp Sensor
PageTop[6509_exhaust_temp_slot1]: <H1>Cat6509 Slot 1 Exhaust Temp
Sensor</H1>
Colours[6509_exhaust_temp_slot1]:
Blue#0066ff,RED#FF0000,GREEN#00eb0c,Orange#ff9933
OIDs ==================================================================
sh env temp
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.25 = .iso.3.6.1.4.1.9.9.91.1.1.1.1.4.26 =
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.27 = .iso.3.6.1.4.1.9.9.91.1.1.1.1.4.28 =
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.29 = VTT1 (Chassis Module)
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.30 =
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.31 = VTT2 (Chassis Module)
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.32 =
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.33 = VTT3 (Chassis Module)
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1001 = intake - slot1
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1002 = Exhaust - slot1
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1003 = device 1 - slot 1
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1004 = device 2 - slot 1
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1007 = intake - slot1 sw eng
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1008 = Exhaust - slot1 sw eng
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1009 = -
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.1010 = -
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.2001 = intake - slot2
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.2002 = Exhaust - slot2
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.2003 = device 1 - slot 2
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.2004 = device 2 - slot 2
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.3001 = intake - slot4
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.3002 = Exhaust - slot4
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.3003 = device 1 - slot 4
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.3004 = device 2 - slot 4
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.4001 = intake - slot5
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.4002 = Exhaust - slot5
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.4003 = device 1 - slot 5
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.4004 = device 2 - slot 5
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.5001 = intake - slot6
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.5002 = Exhaust - slot6
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.5003 = device 1 - slot 6
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.5004 = device 2 - slot 6
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.6001 = intake - slot7
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.6002 = Exhaust - slot7
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.6003 = device 1 - slot 7
.iso.3.6.1.4.1.9.9.91.1.1.1.1.4.6004 = device 2 - slot 7
-----Original Message-----
From: Crow Lee Contr 379 ECS [mailto:Lee.Crow at auab.aorcentaf.af.mil]
Sent: Wednesday, January 22, 2003 6:07 AM
To: mrtg at list.ee.ethz.ch
Subject: [mrtg] Config Maker
Content-Type: text/plain
Ok... I have been reading up on MRTG for a while. I am having a couple of
issues with it, but I'll just address one here for now. This problem may be
obvious to everyone else, but for some reason I am just not getting it.
Let's say I have a Cisco 6513 switch with the following parameters.
IP: 192.168.1.1
RO Community String: grooving
Everyone here probably knows well and good that when I run config maker it
will only give me the configs for interface in/out info. What if I wanted
to monitor a different OID? Can I use config maker with an output variable
to do this or do I just have to know how to write the config?
Say I want to monitor the following OID (Just grabbing one as an example):
CISCO-SMI
1.3.6.1.4.1.9.9.109.1.2.1.1.2.9.9
ciscoMgmt.109.1.2.1.1.2.9.9
TempMon
Can someone please help? What I am actually trying to do is monitor air
intake temperature. We are in a very hot environment, the Middle East, and
this temp. would represent our ITN ambient temperature so that we can keep
our equipment from overheating.
Thanks for the help!
Lee Crow
Senior LAN/WAN Administrator
ITT Systems
_____
DSN: 471-2074
Cell: +974-556-3127
<mailto:Lee.Crow at auab.aorcentaf.af.mil> Lee.Crow at auab.aorcentaf.af.mil
-- Attached file removed by Ecartis and put at URL below --
-- Type: image/gif
-- Size: 2k (2156 bytes)
-- URL : http://www.ee.ethz.ch/~slist/pantomime/27-image001.gif
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
More information about the mrtg
mailing list