[mrtg] Voice-card on Cisco 3640

[Marcos Guerra]

Hi team,

Please, I ask you for assistance, I have a 3640 cisco router running
c3640-is-mz.122-10a.bin and I want to configure a VWIC-1MFT-E1 and as far I
know, to put this controller up, I need to have the command: "voice-card"
into my global configuration and I dont have this option. I dont have the
option "ds0-group" into controller configuration.
My controller is "down" and when I made a physical loop, the controller
changes to "up"

Any idea???

Follow the "sh controller e1" and "sh ver" and a piece of my "sh run"

Thanks in advance.

Marcos Guerra
Brazil

SAOTR002#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-IS-M), Version 12.2(10a), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Mon 20-May-02 21:09 by pwade
Image text-base: 0x60008930, data-base: 0x610D2000

ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE
(fc1)

SAOTR002 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:c3640-is-mz.122-10a.bin"

cisco 3640 (R4700) processor (revision 0x00) with 61440K/4096K bytes of
memory.
Processor board ID 07674154
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Basic Rate ISDN software, Version 1.1.
2 Ethernet/IEEE 802.3 interface(s)
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
1 ISDN Basic Rate interface(s)
1 Channelized E1/PRI port(s)
8 Voice E & M interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x3922

SAOTR002#
SAOTR002#
SAOTR002#sh controller e1 2/0
E1 2/0 is down.
  Applique type is Channelized E1 - unbalanced
  Description: Connection to Siemens PBX
  Receiver is getting AIS.
  alarm-trigger is not set
  Version info Firmware: 20011015, FPGA: 11
  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
  Data in current interval (707 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 707 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 707 Unavail
Secs


SAOTR002#sh run
controller E1 2/0
 framing NO-CRC4
 line-termination 75-ohm
 channel-group 0 timeslots 1-24
 description Connection to Siemens PBX

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi