[mrtg] Re: 64 Kbps CIR 32 Kbps (point to point) Frame Relay WAN (Urgent)

[Winanjaya]

Thanks, but before I continue with my .cfg file, I think I have to inform
you that I am very new with this.. and I use MRTG only (without RRDTool),
below is my .cfg file, I need your advice .. thanks a lot in advance

# Created by
# /usr/bin/cfgmaker --global 'Workdir:
/var/www/html/mrtg/data/proxy-ho' --global 'Workdir:
/var/www/html/mrtg/data/proxy-ho' --show-op-down --output=/etc/mrtg/proxy-ho
.cfg proxy-ho


### Global Config Options

#  for UNIX
# WorkDir: /home/http/mrtg

#  or for NT
# WorkDir: c:\mrtgdata

### Global Defaults

#  to get bits instead of bytes and graphs growing to the right
Options[_]: growright, bits
EnableIPv6: no
Workdir: /var/www/html/mrtg/data/proxy-ho
Icondir: /icons/
Refresh: 600
Interval: 5
RunAsDaemon: yes
######################################################################
# System: proxy-HO.lippogeneral.com
# Description: Linux proxy-HO.lippogeneral.com 2.4.22-1.2115.nptl #1 Wed Oct
29 15:42:51 EST 2003 i686
# Contact: Root <root at localhost> (configure /etc/snmp/snmp.local.conf)
# Location: Unknown (edit /etc/snmp/snmpd.conf)
######################################################################


### Interface 1 >> Descr: 'lo' | Name: '' | Ip: '' | Eth: '' ###
### The following interface is commented out because:
### * it is a Software Loopback interface
#
# Target[proxy-ho_1]: 1:public at proxy-ho:
# SetEnv[proxy-ho_1]: MRTG_INT_IP="" MRTG_INT_DESCR="lo"
# MaxBytes[proxy-ho_1]: 1250000
# Title[proxy-ho_1]: Traffic Analysis for 1 -- proxy-HO.lippogeneral.com
# PageTop[proxy-ho_1]: <H1>Traffic Analysis for 1 --
proxy-HO.lippogeneral.com</H1>
#  <TABLE>
#    <TR><TD>System:</TD>     <TD>proxy-HO.lippogeneral.com in Unknown (edit
/etc/snmp/snmpd.conf)</TD></TR>
#    <TR><TD>Maintainer:</TD> <TD>Root &lt;root at localhost&gt; (configure
/etc/snmp/snmp.local.conf)</TD></TR>
#    <TR><TD>Description:</TD><TD>lo  </TD></TR>
#    <TR><TD>ifType:</TD>     <TD>softwareLoopback (24)</TD></TR>
#    <TR><TD>ifName:</TD>     <TD></TD></TR>
#    <TR><TD>Max Speed:</TD>  <TD>1250.0 kBytes/s</TD></TR>
#  </TABLE>


### Interface 2 >> Descr: 'eth0' | Name: '' | Ip: '' | Eth:
'00-c0-9f-23-77-29' ###

Target[proxy-ho_2]: 2:public at proxy-ho:
SetEnv[proxy-ho_2]: MRTG_INT_IP="" MRTG_INT_DESCR="eth0"
MaxBytes[proxy-ho_2]: 12500000
Title[proxy-ho_2]: Traffic Analysis for 2 -- proxy-HO.lippogeneral.com
PageTop[proxy-ho_2]: <H1>Traffic Analysis for 2 --
proxy-HO.lippogeneral.com</H1>
 <TABLE>
   <TR><TD>System:</TD>     <TD>proxy-HO.lippogeneral.com in Unknown (edit
/etc/snmp/snmpd.conf)</TD></TR>
   <TR><TD>Maintainer:</TD> <TD>Root &lt;root at localhost&gt; (configure
/etc/snmp/snmp.local.conf)</TD></TR>
   <TR><TD>Description:</TD><TD>eth0  </TD></TR>
   <TR><TD>ifType:</TD>     <TD>ethernetCsmacd (6)</TD></TR>
   <TR><TD>ifName:</TD>     <TD></TD></TR>
   <TR><TD>Max Speed:</TD>  <TD>12.5 MBytes/s</TD></TR>
 </TABLE>





----- Original Message -----
From: "Cook, Garry" <GWCOOK at mactec.com>
To: "Winanjaya" <winan888 at cbn.net.id>; <mrtg at list.ee.ethz.ch>
Sent: Tuesday, April 06, 2004 9:41 PM
Subject: RE: [mrtg] 64 Kbps CIR 32 Kbps (point to point) Frame Relay WAN
(Urgent)


mrtg-bounce at list.ee.ethz.ch wrote:
> Dear The Expert,
> We had 64 Kbps CIR 32 Kbps (point to point) Frame Relay WAN
> connection to our branch, is it possible for me to use MRTG
> for make me sure that our Network Provider already gave us
> correct bandwidth rate? if so .. could any body please inform
> me what should I do? or what should I change in my .cfg file?
> I need advice .. I have stuck on this for almost 4 weeks ..
> and I am getting frustated now ..
>
> many thanks in advance
>
> Regards
>
> Winanjaya

Perhaps you could provide some more information, maybe show us your .cfg
file?
If you used configmaker to generate the .cfg file, it should show the
correct bandwidth.
You may want to set MaxBytes to 4000 (for the CIR) and AbsMax to 8000
(for the port). Other than that, I'm not sure what else you are looking
for.
If you still have specific questions about this, please let us know...

Garry W. Cook, CCNA
Network Infrastructure Manager
MACTEC, Inc. - http://www.mactec.com/
303.308.6228 (Office) - 720.220.1862 (Mobile)

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://www.ee.ethz.ch/~slist/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://www.ee.ethz.ch/~slist/lsg2.cgi