[mrtg] Re: 10Gig Interface MaxBytes with Cfg

[Geba, Scott]

I have 2.11.1 I will upgrade to the latest, thanks! 

Scott Geba
Comcast - Eastern Division
200 Cresson Blvd
Oaks, PA 19456
Desk - 610.650.1195
Cell - 267.716.5585
 
-----Original Message-----
From: mrtg-bounce at list.ee.ethz.ch [mailto:mrtg-bounce at list.ee.ethz.ch]
On Behalf Of Pavel Ruzicka
Sent: Saturday, July 15, 2006 5:59 AM
To: mrtg at list.ee.ethz.ch
Cc: Geba, Scott
Subject: [mrtg] Re: 10Gig Interface MaxBytes with Cfg

Hello,

In a Cisco WS-C6509 are 10Gbps interfaces named TenGigabitEthernet
and in a GSR are named GigabitEthernet.
Interface has default bandwidth 10000000 Kbit. This information is
provided via SNMP 64bit OIDs "ifHighSpeed", because "ifSpeed" is too
small. You can override bandwidth in a Cisco router with a command
"bandwidth".
Before few months there was bug in MRTG, that cfgmaker reads ifSpeed
instead of ifHighSpeed and Max speed was wrong. This was probably fixed
in a version 2.13.0 of MRTG. Read CHANGES file for details.
What version do you have?

For me it works perfectly with Cisco 6509 L3 switches and GSR routers.

Best regards,

Pavel Ruzicka

> So I got an answer that the routers don't like to give back the right
> info and the "bandwidth 10000000" command makes it work, which is
> upsetting... oh well, search and replace.
>
> A quick question on the subject though, I was just making a config and
I
> did notice this...
>
> snmpget public at router:::::2:v4only for ifHighSpeed.57 -> 10000 Mb/s
>
> It appears that it sees the right bandwidth there... where does
> ifHighSpeed pull its info from? (on a show int the bw does state
> 10000000kbps, just snmp doesn't pull it back in the ifSpeed)
>
>
>
> -----Original Message-----
> From: mrtg-bounce at list.ee.ethz.ch [mailto:mrtg-bounce at list.ee.ethz.ch]
> On Behalf Of MrPaul
> Sent: Friday, July 14, 2006 12:02 PM
> To: mrtg at list.ee.ethz.ch
> Subject: [mrtg] Re: 10Gig Interface MaxBytes with Cfg
>
> On 7/14/06, Geba, Scott <Scott_Geba at cable.comcast.com> wrote:
> > That I guess is my problem... with an SNMP walk I get this...
> >
> > IF-MIB::ifSpeed.1 = Gauge32: 4294967295
> >
> > I am walking a Cisco 7609. That is whats reported for all 10G and
>
> higher
>
> > (port channels) links. I am using 64bit counters in MRTG (I think...
> > x.x.x.x:::::2)
> >
> > That is also the MaxBytes that is put into MRTG... so apparently
it's
>
> an
>
> > issue with the wrong reported information.
>
> I didn't see this mentioned so I'm going to ask.
>
> Do you have the bandwidth statement set on the interfaces or are you
> relying on IOS to determine that?  I've not run into a problem when I
> specify the bandwidth on the interface.
>
> Paul
>

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://lists.ee.ethz.ch/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://lists.ee.ethz.ch/lsg2.cgi

--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive     http://lists.ee.ethz.ch/mrtg
FAQ         http://faq.mrtg.org    Homepage     http://www.mrtg.org
WebAdmin    http://lists.ee.ethz.ch/lsg2.cgi