[mrtg] MRTG Brocade switch monitoring error
Anson Rinesmith
arinesmith at bigrivertelephone.com
Wed Aug 27 19:59:27 CEST 2008
So replace the name fcswitch with the ip address or put fcswitch in your
hosts file with the IP you want to use. The answer to you problem is right
in the error message.
Skipping host fcswitch as it does not resolve to an IPv4 address
_____
From: mrtg-bounces at lists.oetiker.ch [mailto:mrtg-bounces at lists.oetiker.ch]
On Behalf Of anjini shukla
Sent: Wednesday, August 27, 2008 12:53 PM
To: anjini shukla
Cc: mrtg at lists.oetiker.ch
Subject: Re: [mrtg] MRTG Brocade switch monitoring error
I can ping this host, and reply is IP.xx.xx.xx is alive. I can also do an
snmpwalk with this ip address.:(
Thanks,
Anjini
On Wed, Aug 27, 2008 at 5:02 AM, Matthew Petach <mpetach at yahoo.com> wrote:
The crucial line is
WARNING: Skipping host fcswitch as it does not resolve to an IPv4 address
Make sure that the name you put in your config file is the right
name for the device; if you can't ping it by that name, MRTG can't
do anything as far as monitoring it.
Matt
----- Original Message ----
From: anjini shukla <anjinishukla at gmail.com>
To: mrtg at lists.oetiker.ch
Sent: Tuesday, August 26, 2008 4:56:12 PM
Subject: [mrtg] MRTG Brocade switch monitoring error
Hello,
I am trying to plot graphs for my Brocade 4100 SAN switch and am using
Solaris 10, I am following the documentation given:
http://www.xolution.ch/mrtg/ i have written my config file:
~ snip
Target[switch.IP_0]:
1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12.1&1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11.1:publ
ic at fcswitch
Title[switch.IP_0]: fc throughput on switch fcswitch port 0 (mysun jnic0
slot7)
PageTop[switch.IP_0]: <H1>fc throughput on switch fcswswitch port 0 (mysun
jnic0 slot7)</H1>
~snip
the error message i am getting is:
2008-08-26 12:03:22: WARNING: Skipping host fcswitch as it does not resolve
to an IPv4 address
2008-08-26 12:03:22: WARNING: no data for
1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12&1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11:public at f
cswitch.
Skipping further queries for Host fcswitch in this round.
2008-08-26 12:03:22: ERROR: Target[xxx.xxx.xxx.xx_0][_IN_] '
$target->[0]{$mode} ' did not eval into defined data
2008-08-26 12:03:22: ERROR: Target[xxx.xxx.xxx.xx_0][_OUT_] '
$target->[0]{$mode} ' did not eval into defined data
can any one give me any insight on this, ??
Thanks
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.oetiker.ch/pipermail/mrtg/attachments/20080827/ca459647/attachment.html
More information about the mrtg
mailing list