[mrtg] FW: cisco 6509 graphing problems

[Paul A]

Hi, I have a cisco 6509 that's giving me some issues. 

IOS (tm) s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), 
Version 12.2(18)SXF14, RELEASE SOFTWARE (fc1)


I can graph certain interfaces but not others.

For example I can't graph the following interface:

FastEthernet1/30 is up, line protocol is up (connected)
  Hardware is C6k 100Mb 802.3, address is 000e.83ae.dbad (bia
000e.83ae.dbad)
  Description: To XXX
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:17, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 461000 bits/sec, 326 packets/sec
  5 minute output rate 298000 bits/sec, 329 packets/sec
     46995141 packets input, 8789328879 bytes, 0 no buffer
     Received 1086 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     47580262 packets output, 4758709285 bytes, 0 underruns
     0 output errors, 0 collisions, 3 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

But I CAN graph:

FastEthernet1/25 is up, line protocol is up (connected)
  Hardware is C6k 100Mb 802.3, address is 000e.83ae.dba8 (bia
000e.83ae.dba8)
  Description: To ZZZZ
  MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 100Mb/s
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:48, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 613000 bits/sec, 141 packets/sec
  5 minute output rate 296000 bits/sec, 131 packets/sec
     17065681 packets input, 5772860506 bytes, 0 no buffer
     Received 982 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     16602746 packets output, 4626289121 bytes, 0 underruns
     0 output errors, 0 collisions, 3 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

The interfaces above are setup exactly the same.

This doesn't make sense to me, hoping someone can point me in the right
direction.
FYI im using:

# ./cfgmaker --global "WorkDir: /var/www/mrtg2/6500-fr" --global
"Options[_]: bits,growright" --output ./mrtg.6500.cfg. --ifref=descr
something at 1.1.1.1