[mrtg] Can't create cfg file on Cisco Pix 515

[Kevin Wong]

 Thanks to Mike and everyone.  I realize I used the wrong commend.  I am
good for now.  Moving on...

-----Original Message-----
From: Mike Mitchell [mailto:Mike.Mitchell at sas.com] 
Sent: Friday, April 24, 2009 4:22 PM
To: Kevin Wong
Subject: RE: [mrtg] Can't create cfg file on Cisco Pix 515

Are you running cfgmaker using an already-generated config file?
Cfgmaker should be used to create a config file, not to execute one.

The error message says cfgmaker was trying to do an snmpwalk on the host
named 'mrtg.cfg'.
I think you should pass mrtg.cfg to mrtg instead of cfgmaker, i.e.
        mrtg mrtg.cfg

Mike Mitchell

-----Original Message-----
From: mrtg-bounces at lists.oetiker.ch
[mailto:mrtg-bounces at lists.oetiker.ch] On Behalf Of Kevin Wong
Sent: Friday, April 24, 2009 4:18 PM
To: mrtg at lists.oetiker.ch
Subject: Re: [mrtg] Can't create cfg file on Cisco Pix 515

Yes.  The cfg file does have the correct community name "pace".  See
below... Am I missing something?

### Interface 1 >> Descr: 'Firewall-'outside'-interface' | Name: '' |
Ip: 'xxx.xxx.xxx.xxx' | Eth: '00-0d-bd-a1-84-49' ###

Target[192.168.1.2_1]: 1:pace at 192.168.1.2:
SetEnv[192.168.1.2_1]: MRTG_INT_IP="xxx.xxx.xxx.xxx"
MRTG_INT_DESCR="PIX-Firewall-'outside'-interface"
MaxBytes[192.168.1.2_1]: 12500000
Title[192.168.1.2_1]: Traffic Analysis for 1 -- Firewall
PageTop[192.168.1.2_1]: <h1>Traffic Analysis for 1 -- Firewall</h1>
                <div id="sysdetails">
                        <table>
                                <tr>
                                        <td>System:</td>
                                        <td>Firewall in </td>
                                </tr>
                                <tr>
                                        <td>Maintainer:</td>
                                        <td></td>
                                </tr>
                                <tr>
                                        <td>Description:</td>
 
<td>PIX-Firewall-'outside'-interface  </td>
                                </tr>
                                <tr>
                                        <td>ifType:</td>
                                        <td>ethernetCsmacd (6)</td>
                                </tr>
                                <tr>
                                        <td>ifName:</td>
                                        <td></td>
                                </tr>
                                <tr>
                                        <td>Max Speed:</td>
                                        <td>12.5 MBytes/s</td>
                                </tr>
                                <tr>
                                        <td>Ip:</td>
                                        <td>xxx.xxx.xxx.xxx
(rrcs-24-xxx-230-27.nyc.biz.rr.com)</td>
                                </tr>
                        </table>
                </div>

-----Original Message-----
From: Peter P. Benac [mailto:ppbenac at emacolet.com]
Sent: Friday, April 24, 2009 4:06 PM
To: Kevin Wong; mrtg at lists.oetiker.ch
Subject: RE: [mrtg] Can't create cfg file on Cisco Pix 515

You changed it in the pix, but did you tell MRTG to use the correct
string

----
To have principles...
             First have courage.. With principles comes integrity!!!


-----Original Message-----
From: mrtg-bounces at lists.oetiker.ch
[mailto:mrtg-bounces at lists.oetiker.ch]
On Behalf Of Kevin Wong
Sent: Friday, April 24, 2009 15:58
To: mrtg at lists.oetiker.ch
Subject: Re: [mrtg] Can't create cfg file on Cisco Pix 515

Thanks for the advise.  And yes, I have to enable polling on the pix.
It worked.  However, I get this error when I run it.  Why is it "public"
being used as the community name even I change it?

Error:
  can't resolve "mrtg.cfg" to IP address  at
C:/mrtg-2.16.2/bin\..\lib\mrtg2/SNMP_util.pm line 428 SNMPWALK Problem
for public at mrtg.cfg::::::v4only  at cfgmaker line 950
WARNING: Skipping public at mrtg.cfg: as no info could be retrieved


-----Original Message-----
From: mrtg-bounces at lists.oetiker.ch
[mailto:mrtg-bounces at lists.oetiker.ch] On Behalf Of McDonald, Dan
Sent: Friday, April 24, 2009 2:01 PM
To: mrtg at lists.oetiker.ch
Subject: Re: [mrtg] Can't create cfg file on Cisco Pix 515

On Fri, 2009-04-24 at 13:22 -0400, Kevin Wong wrote:
> Hi,
> I am experiencing an issue trying to create the cfg file.  See below 
> error below.  Can someone point me in the right direction to get this 
> resolved?

snmp has to be explicitly enabled per polling device on the pix.

The syntax changed between version 6.2 and 6.3 and 7.0 (yes, 3
different, incompatible sets of syntax) so allowing "polling" from a
particular host is left as an exercise for the reader...


--
Daniel J McDonald, CCIE #2495, CISSP #78281, CNX Austin Energy
http://www.austinenergy.com

_______________________________________________
mrtg mailing list
mrtg at lists.oetiker.ch
https://lists.oetiker.ch/cgi-bin/listinfo/mrtg

_______________________________________________
mrtg mailing list
mrtg at lists.oetiker.ch
https://lists.oetiker.ch/cgi-bin/listinfo/mrtg