[smokeping-users] FastCGI / Master-/Slave-Systeme

Thu Jul 19 10:05:14 CEST 2012

I also think so.
Thank you,
Have anyone else an idea what's the problem is?

Von: Ryan Becker [mailto:rb14060 at gmail.com]
Gesendet: Donnerstag, 19. Juli 2012 09:43
An: Ackermann, Tobias
Cc: smokeping-users at lists.oetiker.ch
Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme

As I've mentioned before I've been using the fcgi file all along, and it's always contained the same thing that your file does.  It's possible that it's something you need to do with the webserver, though I'm not real familiar in that aspect so I would need someone to jump in and fill us in on that.
On Thu, Jul 19, 2012 at 3:39 AM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Ok.
Did you only change the file like as you wrote or did you also change something else?

Von: Ryan Becker [mailto:rb14060 at gmail.com<mailto:rb14060 at gmail.com>]
Gesendet: Donnerstag, 19. Juli 2012 08:43

An: Ackermann, Tobias
Cc: smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>
Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme

That's what I've got too.
On Thu, Jul 19, 2012 at 2:40 AM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Is it possible that you send me your /smokeping.fcgi file?
Because I think something is wrong with my file.
You can find it attached or see the config here.

#!/bin/sh
/opt/smokeping/bin/smokeping_cgi /opt/smokeping/etc/config

Thank you for support.

Von: Ryan Becker [mailto:rb14060 at gmail.com<mailto:rb14060 at gmail.com>]
Gesendet: Mittwoch, 18. Juli 2012 19:11

An: Ackermann, Tobias
Cc: smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>
Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme

Not sure on this end, then.  I've always stuck to the .fcgi file and never had to switch it around.  Maybe someone else can provide some insight.
On Wed, Jul 18, 2012 at 4:04 AM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Sorry.
If I change the file and the path to the file I got an error.
Smokeping runs at so moment in the Version 2.3.6.

I think I will install the System new.
Have everyone a good manual for the installation so fcgi included?

Tobias
Von: Ryan Becker [mailto:rb14060 at gmail.com<mailto:rb14060 at gmail.com>]
Gesendet: Mittwoch, 18. Juli 2012 08:48

An: Ackermann, Tobias
Cc: smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>
Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme

Wherever it gets served up by your webserver, most likely /var/www/cgi-bin or something similar.  It depends on your OS and Apache configuration.
On Wed, Jul 18, 2012 at 2:46 AM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Hello Ryan,

I found the smokeping.fcgi.dist file and rename it to smokeping.fcgi.
Where can I find the existing Version?

Thank you very much.

Von: Ryan Becker [mailto:rb14060 at gmail.com<mailto:rb14060 at gmail.com>]
Gesendet: Dienstag, 17. Juli 2012 18:34
An: Ackermann, Tobias
Cc: smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>

Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme

It was included in the install directory.  For me it's located at /opt/smokeping/htdocs/smokeping.fcgi.dist.  Rename it to smokeping.fcgi and replace your existing version.
On Tue, Jul 17, 2012 at 12:31 PM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Thank you for your fast answer.
Where can I find this file?

Regards
Tobias
-----------------------------------------------------------------------------------------
________________________________
Von: smokeping-users-bounces+tobias.ackermann=kion-ims.com at lists.oetiker.ch<mailto:kion-ims.com at lists.oetiker.ch> [smokeping-users-bounces+tobias.ackermann=kion-ims.com at lists.oetiker.ch<mailto:kion-ims.com at lists.oetiker.ch>]" im Auftrag von "Ryan Becker [rb14060 at gmail.com<mailto:rb14060 at gmail.com>]
Gesendet: Dienstag, 17. Juli 2012 17:46
Bis: smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>
Betreff: Re: [smokeping-users] FastCGI / Master-/Slave-Systeme
Replace the smokeping.cgi file with the smokeping.fcgi file that comes with it.
On Tue, Jul 17, 2012 at 8:39 AM, Ackermann, Tobias <Tobias.Ackermann at kion-ims.com<mailto:Tobias.Ackermann at kion-ims.com>> wrote:
Hello all,
I have actually on Master-System and two Slave-Systems.
Every system is monitoring 3000 devices.
In the web interface I can see, that there are problems with the graphs.
The measured line is sometimes ticked off.
I read in the internet that's this is a problem of CGI and can solve with a change of FastCGI.
Have everyone done so a change before and could everyone describe that step by step?
Thank you very much!

Regards
Tobias

KION Information Management Services GmbH, Sitz der Gesellschaft: Wiesbaden, Registergericht: Wiesbaden HRB 22949, USt-Id-Nr. DE 254777238, Geschäftsführung: Jeffrey R. Smith (Vorsitzender), Bart Wijnen

_______________________________________________
smokeping-users mailing list
smokeping-users at lists.oetiker.ch<mailto:smokeping-users at lists.oetiker.ch>
https://lists.oetiker.ch/cgi-bin/listinfo/smokeping-users

KION Information Management Services GmbH, Sitz der Gesellschaft: Wiesbaden, Registergericht: Wiesbaden HRB 22949, USt-Id-Nr. DE 254777238, Geschäftsführung: Jeffrey R. Smith (Vorsitzender), Bart Wijnen

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.oetiker.ch/pipermail/smokeping-users/attachments/20120719/e4ced6e0/attachment-0001.htm 