[mrtg] Re: AS5300 ISDN PRI traffic
Stephen
hyss119 at yahoo.com.sg
Thu May 30 07:48:27 MEST 2002
Hi,
I have increased the MaxBytes value to 500 and 1000 but still unable to get
reading on the graph.
Basically, I would like to know the usage for how many channels is in-used
for every five minutes. Is the OID correct?
or necessary config for snmp for this on AS5300? please help. If possible,
can u send me a sample of your mrtg.cfg?
channel no.30 show busy under show ISDN service on AS5300
Ihostname#sh isdn service
PRI Channel Statistics:
ISDN Se0:15, Channel [1-31]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart
5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2
Service State (0=Inservice 1=Maint 2=Outofservice)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
##snmp enable on my as5300##
snmp-server community public RO
snmp-server community private RW
snmp-server community public RO 5
snmp-server ifindex persist
snmp-server packetsize 17940
snmp-server queue-length 200
snmp-server enable traps snmp authentication linkdown linkup coldstart
warmstart
snmp-server enable traps calltracker
snmp-server enable traps modem-health
snmp-server enable traps ds0-busyout
snmp-server enable traps ds1-loopback
snmp-server enable traps isdn call-information
snmp-server enable traps isdn layer2
snmp-server enable traps isdn chan-not-avail
snmp-server enable traps hsrp
snmp-server enable traps config
snmp-server enable traps entity
snmp-server enable traps envmon
snmp-server enable traps aaa_server
snmp-server enable traps bgp
snmp-server enable traps ipmulticast
snmp-server enable traps msdp
snmp-server enable traps rsvp
snmp-server enable traps frame-relay
snmp-server enable traps rtr
snmp-server enable traps syslog
snmp-server enable traps dlsw
snmp-server enable traps dial
snmp-server enable traps dsp card-status
snmp-server enable traps voice poor-qov
snmp-server enable traps xgcp
snmp-server host mrtgserverIP public calltracker
snmp-server host snmpserver public calltracker
snmp-server host snmpserver public calltracker
Please advise. Thanks
stephen
-----Original Message-----
From: Simon Watts [mailto:swatts at connect.com.au]
Sent: Thursday, May 30, 2002 12:35 PM
To: Stephen
Cc: mrtg at list.ee.ethz.ch
Subject: Re: [mrtg] AS5300 ISDN PRI traffic
Without looking/knowing exactly what data you are trying to collect here,
or what your actual problem is, I'd say that the MaxBytes value is too
low.
Doing a quick snmpget for those values on some of our AS5X00's, I'm seeing
values returned like 81, 169, etc. Try raising your MaxBytes to a bigger
values (like 500, or even 1000) and see if you start seeing results then.
Simon
On Thu, 30 May 2002, Stephen wrote:
> Hello There,
>
> I have few Cisco AS5300 for VoIP traffic. I have been trying to use mrtg
> to monitor E1 channels traffic utilization but somehow it doesn't seems to
> be working.
> IOS version is (C5300-IS-M), Version 12.2(5). MRTG 2.9.17
> I would like to monitor the workload for each trunk line(30 channels).
>
> Config is as below;
> PageTop[AS5300]: <H1>cpmISDNBChanInUse4Analog & cpmISDNBChanInUse </H1>
> Target[AS5300]:
>
1.3.6.1.4.1.9.10.19.1.1.2.0&1.3.6.1.4.1.9.10.19.1.1.3.0:readonly at 192.168.0.2
> 54
> Directory[AS5300]: AS5300
> WithPeak[AS5300]: wmy
> Unscaled[AS5300]: dwmy
> Options[AS5300]: growright, nopercent, integer,absolute,gauge
> MaxBytes[AS5300]: 30
> Title[AS5300]: My AS5300 : Async 1-30
> Ylegend[AS5300]: Active Modems
> ShortLegend[AS5300]: Modems
> Legend1[AS5300]: Current Active Modems
> Legend2[AS5300]: Current Active ISDN
> Legend3[AS5300]: 5 minute Average Active Modems
> Legend4[AS5300]: 5 Minute Average Active ISDN
> LegendI[AS5300]: Modems:
> LegendO[AS5300]: ISDN:
>
> It there any necessary SNMP config need to put in on AS5300? CPU load
and
> FE0 traffic is working fine.....
> Can someone enlighten me
>
>
> Thanks in advance.
> stephen
>
>
>
> --
> Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
> Archive http://www.ee.ethz.ch/~slist/mrtg
> FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
> WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
>
>
----------------------------------------------------------------
Simon Watts Assoc. Network Architect 180 Burnley St
swatts at connect.com.au Ph +61 3 8414 3126 Richmond
Connect Internet Sol. Fax +61 3 8414 3115 Vic, Aust, 3121
----------------------------------------------------------------
_________________________________________________________
Do You Yahoo!?
Get your free @yahoo.com address at http://mail.yahoo.com
--
Unsubscribe mailto:mrtg-request at list.ee.ethz.ch?subject=unsubscribe
Archive http://www.ee.ethz.ch/~slist/mrtg
FAQ http://faq.mrtg.org Homepage http://www.mrtg.org
WebAdmin http://www.ee.ethz.ch/~slist/lsg2.cgi
More information about the mrtg
mailing list